Xerox 4260X System Administration Guide - Page 20

Administrator Access, Con Ethernet Settings, Connect the Ethernet Cable, Power on the machine - default password

Page 20 highlights

2 Machine Connection 2. Connect the Ethernet Cable Connect a 10/100 BaseT Ethernet cable to the Ethernet port on the left side of the machine and the other end of the cable to your network port. 3. Power on the machine The Power On button is located on the left side of the machine, to the left as you face the machine. 4. Complete the Steps shown by the Installation Wizard If this is the first time the machine has been powered on, the Installation Wizard will run. Administrator Access The button provides access to the Administrator Tools area. Administrator access is required to change settings such as network information on the device. 1. Press the button on the Control Panel. 2. Enter the Administrator's Password. The default is 1111. 3. Touch [Enter]. 4. Press the button. 5. Touch the [Tools] tab. Configure Ethernet Settings The Ethernet interface will automatically detect the speed of your network. The machine supports hub/switch speeds of: • Auto • 10 Mbps Full-Duplex • 100 Mbps Full-Duplex • 10 Mbps Half-Duplex • 100 Mbps Half-Duplex Set the Ethernet speed on the Xerox machine to match the speed set on your hub or switch: Speed 10HD (Half-Duplex) 100HD 10FD (Full-Duplex) 100FD Auto Machine Setting 10HD or Auto 100HD or Auto 10FD 100FD Auto 8 Xerox WorkCentre 4250/4260 Series System Administration Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210

2
Machine Connection
8
Xerox WorkCentre 4250/4260 Series System Administration Guide
2.
Connect the Ethernet Cable
Connect a 10/100 BaseT Ethernet cable to the Ethernet port on the left side of the
machine and the other end of the cable to your network port.
3.
Power on the machine
The Power On button is located on the left side of the machine, to the left as you face
the machine.
4.
Complete the Steps shown by the Installation Wizard
If this is the first time the machine has been powered on, the Installation Wizard will
run.
Administrator Access
The
<Log In/Out>
button provides access to the Administrator Tools area. Administrator
access is required to change settings such as network information on the device.
1.
Press the
<Log In/Out>
button on the Control Panel.
2.
Enter the Administrator’s
Password
. The default is
1111
.
3.
Touch
[Enter]
.
4.
Press the
<Machine Status>
button.
5.
Touch the
[Tools]
tab.
Configure Ethernet Settings
The Ethernet interface will automatically detect the speed of your network. The machine
supports hub/switch speeds of:
Auto
10 Mbps Full-Duplex
100 Mbps Full-Duplex
10 Mbps Half-Duplex
100 Mbps Half-Duplex
Set the Ethernet speed on the Xerox machine to match the speed set on your hub or switch:
Speed
Machine Setting
10HD (Half-Duplex)
10HD or Auto
100HD
100HD or Auto
10FD (Full-Duplex)
10FD
100FD
100FD
Auto
Auto