Yamaha DSP-E200 Owner's Manual - Page 17

Notes About The Remote Control Transmitter, Specifications

Page 17 highlights

NOTES ABOUT THE REMOTE CONTROL TRANSMITTER Battery installation Remote-control transmitter operation range 1 3 Remote-control sensor 2 Battery replacement If you find that the remote control transmitter must be used closer to the main unit, the batteries are weak. Replace both batteries with new ones. Notes q Use only AA, R6, UM-3 batteries for replacement. q Be sure the polarities are correct. (See the illustration inside the battery compartment.) q Remove the batteries if the remote control transmitter will not be used for an extended period of time. q If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. Within approximately 7 m (23 feet) 30° 30° Notes q There should be no large obstacles between the remote control transmitter and the main unit. q If the remote control sensor is directly illuminated by strong lighting (especially an inverter type of fluorescent lamp etc.), it might cause the remote control transmitter not to work correctly. In this case, reposition the main unit to avoid direct lighting. SPECIFICATIONS Minimum RMS Output Power per Channel Center (8 ohms, 20 Hz - 20 kHz, 0.08% THD 25W Rear L, R (8 ohms, 1 kHz, 0.3% THD 25W+25W Input Sensitivity/Impedance INPUT 150 mV/47 k-ohms Output Level/Impedance MAIN OUT/CENTER OUT 1V/1 k-ohms Frequency Response (20 Hz to 20 kHz) INPUT to MAIN OUT 0±0.5 dB Total Harmonic Distortion (20 Hz to 20 kHz) INPUT to MAIN OUT (1 V 0.01% Signal-to-Noise Ratio (IHF-A Network) MAIN OUT (Input Shorted 95 dB Residual Noise (IHF-A Network) MAIN OUT 5 µV Channel Separation (Input 5.1 k-ohms Shorted 1 kHz/10 kHz 65 dB/50 dB Power Supply [U.S.A. and Canada models AC 120 V, 60 Hz [Australia and U.K. models AC 240 V, 50 Hz [Europe model AC 230 V, 50 Hz [General model AC 110/120/220/240V, 50/60 Hz Power Consumption 90W AC Outlet 1 UNSWITCHED OUTLET 200W max. total Dimensions (W x H x D 435 x 151.3 x 296.7 mm (17-1/8" x 5-15/16" x 11-11/16") Weight 7.7 kg (16 lbs. 15 oz.) Accessories Remote control transmitter Batteries Audio connection cord x 2 Specifications subject to change without notice. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19

17
NOTES ABOUT THE REMOTE CONTROL TRANSMITTER
Battery installation
Battery replacement
If you find that the remote control transmitter must be used
closer to the main unit, the batteries are weak.
Replace both
batteries with new ones.
Notes
Use only AA, R6, UM-3 batteries for replacement.
Be sure the polarities are correct.
(See the illustration inside
the battery compartment.)
Remove the batteries if the remote control transmitter will
not be used for an extended period of time.
If batteries leak, dispose of them immediately.
Avoid
touching the leaked material or letting it come in contact with
clothing, etc.
Clean the battery compartment thoroughly
before installing new batteries.
Remote-control transmitter operation range
Notes
There should be no large obstacles between the remote
control transmitter and the main unit.
If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp etc.),
it might cause the remote control transmitter not to work
correctly. In this case, reposition the main unit to avoid
direct lighting.
SPECIFICATIONS
Minimum RMS Output Power per Channel
Center (8 ohms, 20 Hz – 20 kHz, 0.08% THD)
..........................................................................................
25W
Rear L, R (8 ohms, 1 kHz, 0.3% THD)
...................
25W+25W
Input Sensitivity/Impedance
INPUT
.........................................................
150 mV/47 k-ohms
Output Level/Impedance
MAIN OUT/CENTER OUT
....................................
1V/1 k-ohms
Frequency Response (20 Hz to 20 kHz)
INPUT to MAIN OUT
..................................................
0±0.5 dB
Total Harmonic Distortion (20 Hz to 20 kHz)
INPUT to MAIN OUT (1 V)
.............................................
0.01%
Signal-to-Noise Ratio (IHF-A Network)
MAIN OUT (Input Shorted)
..............................................
95 dB
Residual Noise (IHF-A Network)
MAIN OUT
.........................................................................
5 μV
Channel Separation
(Input 5.1 k-ohms Shorted 1 kHz/10 kHz)
...............
65 dB/50 dB
Power Supply
[U.S.A. and Canada models]
.......................
AC 120 V, 60 Hz
[Australia and U.K. models]
.........................
AC 240 V, 50 Hz
[Europe model]
............................................
AC 230 V, 50 Hz
[General model]
..................
AC 110/120/220/240V, 50/60 Hz
Power Consumption
............................................................
90W
AC Outlet
1 UNSWITCHED OUTLET
...........................
200W max. total
Dimensions (W x H x D)
.......................
435 x 151.3 x 296.7 mm
(17-1/8” x 5-15/16” x 11-11/16”)
Weight
......................................................
7.7 kg (16 lbs. 15 oz.)
Accessories
......................................
Remote control transmitter
Batteries
Audio connection cord x 2
Specifications subject to change without notice.
2
3
1
30
°
30
°
Remote-control
sensor
Within approximately
7 m (23 feet)