Yamaha RX-395RDS Owner's Manual - Page 14

Basic Operations

Get Yamaha RX-395RDS PDF manuals and user guides View all Yamaha RX-395RDS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

BASIC OPERATIONS 2 3 1, 6 4 TO PLAY A SOURCE 1 Set to the " ∞ " position. 2 Turn the power on. POWER 7 4 Select the speakers to be used. SPEAKERS A B ON ON OFF OFF * If you use two speaker systems, press both the A and B switches. 5 Play the source. (For detailed information on the tuning operation, refer to page 17.) 6 3 Select the desired input source by using the input selector buttons. RX-495RDS TUNER CD MONITOR TAPE 2 TAPE 1 AUX PHONO COPY RX-395, RX-395RDS TUNER CD TAPE MONITOR AUX PHONO * The name of the selected input source will appear on the display. * Note that pressing on each input selector button selects the source which is connected to the corresponding input terminals on the rear panel. 14 Adjust to the desired output level. 7 If desired, adjust the BASS, TREBLE, BALANCE and LOUDNESS controls, etc. (refer to page 16). Notes RX-495RDS only q If you select AUX, TUNER, CD or PHONO, be sure that TAPE 1 and/or TAPE 2 are not being selected. q If you select TAPE 1 and TAPE 2 at the same time, the result will be the sound from the tape deck 1. q For TAPE 1 and TAPE 2, whenever the button is pressed, the corresponding input source is selected or canceled alternately. RX-395 and RX-395RDS only q Whenever the TAPE MONITOR is pressed, the tape deck is selected or canceled alternately. q If both TAPE MONITOR and another input selector button are selected, TAPE MONITOR takes priority of another input selector button. To turn off the power Press the POWER switch again.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
14
BASIC OPERATIONS
TO PLAY A SOURCE
SPEAKERS
A
ON
OFF
B
ON
OFF
TAPE 1
TAPE 2
MONITOR
AUX
PHONO
TUNER
CD
COPY
TAPE
MONITOR
AUX
PHONO
TUNER
CD
3
1, 6
2
4
7
POWER
RX-495RDS
RX-395, RX-395RDS
1
Set to the “
∞
” position.
2
Turn the power on.
3
Select the desired input source by using the input
selector buttons.
* The name of the selected input source will appear on the
display.
* Note that pressing on each input selector button selects the
source which is connected to the corresponding input
terminals on the rear panel.
4
Select the speakers to be used.
*
If you use two speaker systems, press both the A and
B switches.
5
Play the source.
(For detailed information on the
tuning operation, refer to page 17.)
6
Adjust to the desired output level.
7
If desired, adjust the
BASS, TREBLE, BALANCE
and
LOUDNESS
controls, etc. (refer to page 16).
Notes
RX-495RDS only
●
If you select
AUX
,
TUNER
,
CD
or
PHONO
, be sure that
TAPE 1
and/or
TAPE 2
are not being selected.
●
If you select
TAPE 1
and
TAPE 2
at the same time, the
result will be the sound from the tape deck 1.
●
For
TAPE 1
and
TAPE 2
, whenever the button is pressed,
the corresponding input source is selected or canceled
alternately.
RX-395 and RX-395RDS only
●
Whenever the
TAPE MONITOR
is pressed, the tape deck
is selected or canceled alternately.
●
If both
TAPE MONITOR
and another input selector button
are selected,
TAPE MONITOR
takes priority of another
input selector button.
To turn off the power
Press the
POWER
switch again.