Zanussi ZWI71201WA Product Manaul - Page 26

and tighten the screw again.

Get Zanussi ZWI71201WA PDF manuals and user guides View all Zanussi ZWI71201WA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

• a) Door The dimensions of the door should be: - width 595-598 mm - thickness 16-22 mm The height (C-Fig. C) depends on the height of the adjacent furniture's base. • b) Hinges To mount the hinges it is necessary to drill two holes (dia. 35 mm, depth 12.5-14 mm depending on the depth of door furniture) on the inner side of the door. The distance between the holes hobs fixing centres must be 416 mm. The distance (B) from upper edge of the door to the centre of the hole depends on the adjacent furniture's dimensions. The required dimensions are given in the picture C. The hinges will be fixed to the door by means of screws for wood (2-Fig. B) supplied with the appliance. • c) Mounting the door Fix the hinges (1) to the machine by means of the M 5x15 screws (3-Fig. B). The hinges can be adjusted to compensate for possible uneven thickness of the door. To align the door perfectly it is necessary to loosen the screw (3-Fig. B), adjust the door and tighten the screw again. 4 6 8 Caution! Do not remove the screw 8! d) Counter-magnet (6) The appliance is prearranged for a magnetic closure of the door. To enable a correct operation of this device, it is necessary to screw the counter-magnet (6) (steel disk + rubber ring) into the inner side of the door. Its position must correspond to the magnet (4) on the appliance (see picture D). 6 45 E 1 7 3 82 Caution! Do not remove the screw 8! If the door has to be opened from left to right, invert the position of the plates (7), the magnet (4) and the plate (5) (Fig. B and E). Mount the counter-magnet (6) and the hinges (1) as previously described. Recommendations regarding the construction and fitting of a base when the installation requires an integrated appliance to be raised. D 26 www.zanussi.com

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
•
a) Door
The dimensions of the door should be:
- width 595-598 mm
- thickness 16-22 mm
The height (C-Fig. C) depends on the height
of the adjacent furniture's base.
•
b) Hinges
To mount the hinges it is necessary to drill
two holes (dia. 35 mm, depth 12.5-14 mm
depending on the depth of door furniture) on
the inner side of the door. The distance be-
tween the holes hobs fixing centres must be
416 mm.
The distance (B) from upper edge of the door
to the centre of the hole depends on the ad-
jacent furniture's dimensions.
The required dimensions are given in the pic-
ture
C
.
The hinges will be fixed to the door by means
of screws for wood (2-Fig.
B
) supplied with
the appliance.
•
c) Mounting the door
Fix the hinges (1) to the machine by means of
the M 5x15 screws (3-Fig.
B
). The hinges
can be adjusted to compensate for possible
uneven thickness of the door.
To align the door perfectly it is necessary to
loosen the screw (3-Fig.
B
), adjust the door
and tighten the screw again.
D
4
6
8
Caution!
Do not remove the screw
8
!
d) Counter-magnet (6)
The appliance is prearranged for a magnetic
closure of the door.
To enable a correct operation of this device, it
is necessary to screw the counter-magnet (6)
(steel disk + rubber ring) into the inner side
of the door. Its position must correspond to
the magnet (4) on the appliance (see picture
D
).
E
1
2
3
7
5
6
4
8
Caution!
Do not remove the screw
8
!
If the door has to be opened from left to right,
invert the position of the plates (7), the mag-
net (4) and the plate (5) (Fig.
B
and
E
).
Mount the counter-magnet (6) and the hinges
(1) as previously described.
Recommendations regarding the con-
struction and fitting of a base when the
installation requires an integrated appli-
ance to be raised.
26
www.zanussi.com