2013 Kawasaki Brute Force 650 4x4 Owners Manual - Page 44

2013 Kawasaki Brute Force 650 4x4 Manual

Get 2013 Kawasaki Brute Force 650 4x4 PDF manuals and user guides View all 2013 Kawasaki Brute Force 650 4x4 manuals

Page 44 highlights

42 GENERAL INFORMATION Oil Pressure Warning Indicator Light: The "LED" (Light Emitting Diode) oil pressure warning indicator light flashes to warn the operator whenever the oil pressure is dangerously low or the ignition key is in the "ON" position with the engine not running, and goes off when the engine oil pressure is high enough. Refer to the MAINTENANCE AND ADJUSTMENT chapter for more detailed engine oil information. Belt Check Indicator Light: This vehicle is equipped with a drive belt failure detection system. Excessive belt wear or belt damage will activate a switch in the transmission cover causing the belt check indicator light to flash at intervals of 0.35 seconds. The indicator also serves as an hour meter to indicate when periodic maintenance should be performed. The indicator turns on steadily when the vehicle has been used for a total of 100 hours of operation. When the belt check indicator light goes on, return the vehicle to the dealer immediately for inspections, adjustment, and/or repairs as necessary. Refer to the "Belt Drive Transmission" section on the "Maintenance and Adjustment" chapter. and broken, while the main switch is on, the indicator light also starts flashing. In this case as well, you need to return the vehicle to the dealer for reset and adjustment. j NOTICE The Belt Check Indicator Light comes on after 100 hours of operation as a reminder that the drive belt must be inspected for wear. NOTE żWhen the lead connector for the drive belt check indicator is disconnected or the lead itself is cut

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
42
GENERAL INFORMATION
j
Oil Pressure Warning Indicator Light:
The “LED” (Light Emitting Diode) oil pressure
warning indicator light flashes to warn the operator
whenever the oil pressure is dangerously low or the
ignition key is in the “ON” position with the engine
not running, and goes off when the engine oil pres-
sure is high enough. Refer to the MAINTENANCE
AND ADJUSTMENT chapter for more detailed en-
gine oil information.
Belt Check Indicator Light:
This vehicle is equipped with a drive belt failure de-
tection system. Excessive belt wear or belt damage
will activate a switch in the transmission cover caus-
ing the belt check indicator light to flash at intervals
of 0.35 seconds.
The indicator also serves as an hour meter to in-
dicate when periodic maintenance should be per-
formed.
The indicator turns on steadily when the
vehicle has been used for a total of 100 hours of op-
eration.
When the belt check indicator light goes on, return
the vehicle to the dealer immediately for inspections,
adjustment, and/or repairs as necessary.
Refer to the “Belt Drive Transmission” section on
the “Maintenance and Adjustment” chapter.
NOTE
°
When the lead connector for the drive belt check
indicator is disconnected or the lead itself is cut
and broken, while the main switch is on, the indi-
cator light also starts flashing. In this case as well,
you need to return the vehicle to the dealer for re-
set and adjustment.
NOTICE
The Belt Check Indicator Light comes on af-
ter 100 hours of operation as a reminder that
the drive belt must be inspected for wear.