2009 Polaris 600 Switchback Owners Manual - Page 116

2009 Polaris 600 Switchback Manual

Get 2009 Polaris 600 Switchback PDF manuals and user guides View all 2009 Polaris 600 Switchback manuals

Page 116 highlights

Steering System n Ski Skags MAINTENANCE WARNING Worn skis and/or skags will adversely affect handling. Loss of vehicle control may result, causing serious injury or death. See your dealer's studding chart for recommended skags. If you install longer or more aggressive carbide skags than the original equipment, it may also be necessary to add track studs to maintain proper vehicle control while turning on hard-packed snow or ice. Check skags before each use of the snowmobile to ensure positive steering characteristics. Skags must be replaced when worn to half their original diameter. TIP: Carbide skags must be replaced if any abnormal wear or chipping is found. Skag Replacement Some models are equipped with single skags. Some models are equipped with dual skags. 1. Raise and support the front of the machine so the skis are approximately 6I (15.2 cm) from the ground. 2. Remove the attaching nuts and pry the skag downward. 3. Remove the front end of the skag. 4. Remove the rear end of the skag. 5. Reverse the steps to install a skag. Skag 113

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
113
MAINTENANCE
Steering System
n
Ski Skags
Check skags before each use of the snowmobile to ensure positive steer-
ing characteristics. Skags must be replaced when worn to half their orig-
inal diameter.
TIP:
Carbide skags must be replaced if any abnormal wear or chipping is found.
Skag Replacement
Some models are equipped with single skags. Some models are
equipped with dual skags.
1.
Raise and support the front of
the machine so the skis are
approximately 6
I
(15.2 cm)
from the ground.
2.
Remove the attaching nuts and
pry the skag downward.
3.
Remove the front end of the
skag.
4.
Remove the rear end of the
skag.
5.
Reverse the steps to install a
skag.
WARNING
Worn skis and/or skags will adversely affect handling. Loss of vehicle control
may result, causing serious injury or death.
See your dealer's studding chart for recommended skags. If you install longer
or more aggressive carbide skags than the original equipment, it may also be
necessary to add track studs to maintain proper vehicle control while turning
on hard-packed snow or ice.
Skag