2000 Volvo S40 Owner's Manual - Page 33

2000 Volvo S40 Manual

Get 2000 Volvo S40 PDF manuals and user guides View all 2000 Volvo S40 manuals

Page 33 highlights

· Avoid using the air conditioning when it is not required. When engaged, the air conditioner's compressor places an additional load on the engine. However, please note that fuel consumption is lower with the air conditioning on than it is when driving with the air conditioning switched off and the windows down. · Utilizing the fuel consumption modes in the Trip Computer can help you "learn" how to drive more economically. Other factors which decrease gas mileage are: · Worn or dirty spark plugs · Incorrect spark plug gap · Dirty air cleaner · Dirty engine oil and clogged oil filter · Dragging brakes · Incorrect front end alignment Some of the above mentioned items and others are checked at the standard Maintenance Service intervals. NOTE : The automatic transmission's ( D)rive position should be used as often as possible to help improve fuel economy. WARNING! It is recommended that tires of the same make and dimensions be used on all four wheels (including the use of snow tires). Do not use bias ply tires as this will adversely alter vehicle handling characteristics. Maintain correct tire pressure. pg. 61 Starting the engine Starting and stopping 1. Fasten the seat belt. WARNING! Before starting, check that the seat, steering wheel and mirrors are adjusted properly. Make sure the brake pedal can be depressed completely. Move the seat closer if necessary. Refer to section "front seats". 2. Apply the parking brake, if not already set. The gear selector is locked in the ( P)ark position (SHIFT LOCK). 3. Without touching the accelerator pedal, turn the ignition key to the starting position. Allow the starter to operate for up to 5 seconds. Release the key as soon as the engine starts. If the engine fails to start, repeat step 3. For cold starts at altitudes above 6000 ft (1800 meters), depress the accelerator pedal halfway and turn the key to the starting position. Release the pedal slowly when the engine starts. 4. To release the gear selector from the (P)ark position, the ignition key must be in position II and the brake pedal must be depressed. See page 95 for instructions on manually releasing the SHIFTLOCK system. NOTE: Your car is equipped with a KEYLOCK system. When the engine is switched off, the gear selector must be in the ( P)ark position before the starting key can be removed from the ignition switch. 5. Select the desired gear. The gear engages after a slight delay which is especially noticeable when selecting R.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
· Avoid using the air conditioning when it is not required. When engaged, the air conditioner's compressor places an
additional load on the engine. However, please note that fuel consumption is lower with the air conditioning on than it
is when driving with the air conditioning switched off and the windows down.
· Utilizing the fuel consumption modes in the Trip Computer can help you "learn" how to drive more economically.
Other factors which decrease gas mileage are:
· Worn or dirty spark plugs
· Incorrect spark plug gap
· Dirty air cleaner
· Dirty engine oil and clogged oil filter
· Dragging brakes
· Incorrect front end alignment
Some of the above mentioned items and others are checked at the standard Maintenance Service intervals.
NOTE
: The automatic transmission's (
D
)rive position should be used as often as possible to help improve fuel
economy.
WARNING!
It is recommended that tires of the same make and dimensions be used on all four wheels (including the use of snow
tires). Do not use bias ply tires as this will adversely alter vehicle handling characteristics. Maintain correct tire
pressure.
pg. 61 Starting the engine
Starting and stopping
1. Fasten the seat belt.
WARNING!
Before starting, check that the seat, steering wheel and mirrors are adjusted properly. Make sure the brake pedal can
be depressed completely. Move the seat closer if necessary. Refer to section "front seats".
2
. Apply the parking brake, if not already set. The gear selector
is locked in the (
P
)ark position
(SHIFT LOCK).
3.
Without touching the accelerator pedal,
turn the ignition key to the starting position. Allow the starter to operate
for up to 5 seconds. Release the key as soon as the engine starts. If the engine fails to start, repeat step 3.
For cold starts at altitudes above 6000 ft (1800 meters), depress the accelerator pedal halfway and turn the key to the
starting position. Release the pedal slowly when the engine starts.
4.
To release the gear selector from the (P)ark position, the ignition key must be in position II and the brake pedal
must be depressed.
See
page 95
for instructions on manually releasing the SHIFTLOCK system.
NOTE:
Your car is equipped with a
KEYLOCK
system. When the engine is switched off, the gear selector must be
in the (
P
)ark position before the starting key can be removed from the ignition switch.
5.
Select the desired gear. The gear engages after a slight delay which is especially noticeable when selecting R.