3M X75 Operation Guide - Page 4

About Restart switch - projector

Get 3M X75 PDF manuals and user guides View all 3M X75 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

Part names Part names Projector Zoom knob (18) Focus ring (18) Vent (6) Lens (16) Front-Right side Lamp door (45) (Lamp unit is inside.) Remote sensor (15) Speaker Elevator button (8) Elevator foot (8) Filter cover (46) (Air filter and intake vent are inside.) Control buttons (5) (See the following page.) Ports (See below.) Bottom side AC inlet (13) Power switch (16) Rear-Left side Speaker Elevator button (8) Elevator foot (8) Vent (6) DC OUT port USB port (11) COMPONENT VIDEO ports (12) Y CB/PB CR/PR LAN port (12) LAN USB DC OUT RGB IN1 COMPONENT VIDEO RGB OUT CR/PR CB/PB Y Restart switch (*) (52) RGB IN1 port (11) RGB IN2 DVI-D AUDIO-IN AUDIO-OUT DVI-D port (11) RGB IN2 port (11) CONTROL REMOTE CONTROL AUDIO OUT port (11) AUDIO IN port (11) AUDIO IN L/R port (12) VIDEO port (12) S-VIDEO port (12) R-AUDIO IN-L VIDEO S-VIDEO Ports WIRED REMOTE port CONTROL port (11) RGB OUT port (11) NOTE (*) About Restart switch: This Projector is controlled by an internal microprocessor. Under certain exceptional circumstances, the projector may not operate correctly and the microprocessor will need to be reset. In such a case, please push the Restart switch by using a cocktail stick or similar, and before turning on again, make the projector cool down at least 10 minutes without operating. Only push the Restart switch in these exceptional instances. 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
4
Y
VIDEO
RGB IN1
RGB IN2
DVI-D
RGB OUT
CONTROL
AUDIO-IN
REMOTE
CONTROL
USB
DC OUT
S-VIDEO
LAN
COMPONENT VIDEO
C
B
/P
B
C
R
/P
R
R-AUDIO IN-L
AUDIO-OUT
Part names
Lens (
16
)
Filter cover (
46
)
(Air filter and intake vent
are inside.)
Elevator button (
8
)
Elevator foot (
8
)
Remote sensor (
15
)
Zoom knob (
18
)
Focus ring (
18
)
Vent (
6
)
AC inlet (
13
)
Power switch (
16
)
Elevator button (
8
)
COMPONENT
VIDEO ports (
12
)
Y
C
B
/P
B
C
R
/P
R
S-VIDEO port (
12
)
VIDEO port (
12
)
CONTROL port (
11
)
Part names
Projector
Lamp door (
45
)
(Lamp unit is inside.)
Elevator foot (
8
)
Bottom side
Speaker
Front-Right side
Rear-Left side
Control buttons (
5
)
(See the following page.)
Ports (See below.)
Vent (
6
)
AUDIO OUT port (
11
)
Ports
AUDIO IN port (
11
)
AUDIO IN L/R port (
12
)
USB port (
11
)
RGB IN1 port (
11
)
RGB IN2 port (
11
)
DVI-D port (
11
)
NOTE
(*) About Restart switch:
This Projector is controlled by an internal
microprocessor. Under certain exceptional circumstances, the projector may not
operate correctly and the microprocessor will need to be reset. In such a case,
please push the Restart switch by using a cocktail stick or similar, and before
turning on again, make the projector cool down at least 10 minutes without
operating. Only push the Restart switch in these exceptional instances.
Restart switch (*) (
52
)
RGB OUT port (
11
)
WIRED REMOTE port
DC OUT port
LAN port (
12
)