3M X75 Safety Guide - Page 10

Lamp

Get 3M X75 PDF manuals and user guides View all 3M X75 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

ENGLISH Lamp Lamp Operation: The following symptoms may indicate a lamp in need of replacement: • LAMP indicator lights up red. • "CHANGE THE LAMP" message appears on the screen. WARNING • To reduce the risk associated with air or ground water contamination, which if not avoided could result in death or serious injury: - The lamp in this product contains mercuy. Dispose of projection lamp in a manner that is consistent with your local hazardous waste regulations for mercury. - For recycling and disposal information, contact your respective governmental agencies. In U.S., contact the Electronic Industries Alliance at www.lamprecycle.org In Canada, contact the Electronic Product Stewardship Canada at www.epsc.ca Display Lamp Operation Hours To determine the lamp operation hours, follow these steps: 1. While the projector is running, press the MENU button on the remote control. Choose the "OPTION" using the button, and press the button or the ENTER button. Choose the "LAMP TIME" using the button. 2. The operating time of the lamp will be displayed. The message "CHANGE THE LAMP, AFTER REPLACING LAMP RESET THE LAMP TIMER" will appear after the lamp operating hours have reached the end of the normal lamp life. The message "POWER WILL TURN OFF AFTER 20 HOURS" will appear when 20 or less lamp hours remain. The number of hours left until shut down will decrease until 0 hour is reached, then power will be turned off. √ Note After normal lamp operating time has expired, the projector will only run for 10-minute intervals when restarted until the lamp is replaced and the lamp timer is reset. The message "CHANGE THE LAMP" will blink at projector start up to remind you to change the lamp. Reset Lamp Hours 1. While the projector is running, press the MENU button on the remote control. Choose the "OPTION" using the button, and press the button or the ENTER button. 2. Choose the "LAMP TIME" using the button, and press and hold the RESET button on the remote control for 3 seconds. 3. The reset menu will then appear. After you replace the lamp with a new lamp, select "RESET" on the menu with the button. 10 3M™ Multimedia Projector X75 Product Safety Guide © 3M 2005

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
3M™ Multimedia Projector X75 Product Safety Guide
© 3M 2005
10
Lamp
Lamp Operation:
The following symptoms may indicate a lamp in need of replacement:
• LAMP indicator lights up red.
• “CHANGE THE LAMP” message appears on the screen.
•
To reduce the risk associated with air or ground water contamination, which if
not avoided could result in death or serious injury:
-
The lamp in this product contains mercuy. Dispose of projection lamp in a manner
that is consistent with your local hazardous waste regulations for mercury.
-
For recycling and disposal information, contact your respective governmental
agencies.
In U.S., contact the Electronic Industries Alliance at www.lamprecycle.org
In Canada, contact the Electronic Product Stewardship Canada at www.epsc.ca
WARNING
Display Lamp Operation Hours
To determine the lamp operation hours, follow these steps:
1.
While the projector is running, press the MENU button on the remote control.
Choose the “OPTION” using the
button, and press the
button or the ENTER button.
Choose the “LAMP TIME” using the
button.
2.
The operating time of the lamp will be displayed. The message “CHANGE THE LAMP,
AFTER REPLACING LAMP RESET THE LAMP TIMER” will appear after the lamp
operating hours have reached the end of the normal lamp life. The message “POWER
WILL TURN OFF AFTER 20 HOURS” will appear when 20 or less lamp hours remain.
The number of hours left until shut down will decrease until 0 hour is reached, then
power will be turned off.
√
Note
After normal lamp operating time has expired, the projector will only run for 10-minute
intervals when restarted until the lamp is replaced and the lamp timer is reset. The message
“CHANGE THE LAMP” will blink at projector start up to remind you to change the lamp.
Reset Lamp Hours
1.
While the projector is running, press the MENU button on the remote control.
Choose the “OPTION” using the
button, and press the
button or the ENTER
button.
2.
Choose the “LAMP TIME” using the
button, and press and hold the RESET button on
the remote control for 3 seconds.
3.
The reset menu will then appear. After you replace the lamp with a new lamp, select
“RESET” on the menu with the
button.
ENGLISH