3M X75 Safety Guide - Page 8

Important Note, and shut down.

Get 3M X75 PDF manuals and user guides View all 3M X75 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

ENGLISH Important Note 1. Always open the lens shutter or remove lens cap when the projection lamp is on. 2. To avoid premature lamp failure, do not change the mounting position of the projector (desktop ceiling mount or ceiling desktop mount) and continue to use the same lamp. 3. To avoid reduced lamp life, do not touch projection lamp with bare fingers. 4. To avoid reduced image quality, do not touch projection lens or other internal optical components. 5. Do not use detergents, chemicals, or any spray liquids for cleaning this unit, other than those referred to in the "Operators Guide". 6. For maximum lamp life, do not strike or drop, improperly handle, or scratch the lamp glass. Also, do not install an old or used lamp. 7. Keep air filter clean. Refer to the cleaning instructions contained in the "Operator's Guide". 8. Keep all ventilation openings free of any obstructions. 9. In some countries, the line voltage is NOT stable. This projector is designed to operate safely within a bandwidth of 90 to 132 volts / 198 to 264 volts (50 to 60 Hz) ±10 volts, but could fail if power drops or surges of ±10 volts occur. In these highrisk areas, it is recommended to install a power stabilizer unit. 10. Do not block intake or exhaust air vents. This will cause the projector to over heat and shut down. 11. Do not place the projector in direct sunlight or near a hot object such as a heater. 12. To prevent damaging the projector, always hold the projector whenever using the elevator buttons to adjust the elevator feet. 13. Use the accessory cable or a designated-type cable for the connection. Some cables have to be used with core set. A too long cable may cause certain picture degradation. Please consult with your dealer for details. For cables that have a core only at one end, connect the core to the projector. 14. Make sure that you connect devices to the correct port. Incorrect connection may result in malfunction and/or damage to the device and/or projector. 15. Do not place the projector in the side/front/rear-up position, except care of the air filter. 8 3M™ Multimedia Projector X75 Product Safety Guide © 3M 2005

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
3M™ Multimedia Projector X75 Product Safety Guide
© 3M 2005
8
ENGLISH
Important Note
1.
Always open the lens shutter or remove lens cap when the projection lamp is on.
2.
To avoid premature lamp failure, do not change the mounting position of the
projector (desktop ceiling mount or ceiling desktop mount) and continue to use the
same lamp.
3.
To avoid reduced lamp life, do not touch projection lamp with bare fingers.
4.
To avoid reduced image quality, do not touch projection lens or other internal
optical components.
5.
Do not use detergents, chemicals, or any spray liquids for cleaning this unit, other
than those referred to in the “Operators Guide”.
6.
For maximum lamp life, do not strike or drop, improperly handle, or scratch the
lamp glass. Also, do not install an old or used lamp.
7.
Keep air filter clean. Refer to the cleaning instructions contained in the “Operator’s
Guide”.
8.
Keep all ventilation openings free of any obstructions.
9.
In some countries, the line voltage is NOT stable. This projector is designed to
operate safely within a bandwidth of 90 to 132 volts / 198 to 264 volts (50 to 60 Hz)
±10 volts, but could fail if power drops or surges of ±10 volts occur. In these high-
risk areas, it is recommended to install a power stabilizer unit.
10.
Do not block intake or exhaust air vents. This will cause the projector to over heat
and shut down.
11.
Do not place the projector in direct sunlight or near a hot object such as a heater.
12.
To prevent damaging the projector, always hold the projector whenever using the
elevator buttons to adjust the elevator feet.
13.
Use the accessory cable or a designated-type cable for the connection. Some
cables have to be used with core set. A too long cable may cause certain picture
degradation. Please consult with your dealer for details. For cables that have a
core only at one end, connect the core to the projector.
14.
Make sure that you connect devices to the correct port. Incorrect connection may
result in malfunction and/or damage to the device and/or projector.
15.
Do not place the projector in the side/front/rear-up position, except care of the air
filter.