3Ware 8506-4LP User Guide - Page 30

Connect the drives to the interface cables

Get 3Ware 8506-4LP - Escalade RAID Controller PDF manuals and user guides
UPC - 693494850642
View all 3Ware 8506-4LP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

3ware Hardware Installation Note: The connectors on the end of the controller are susceptible to damage from excessive bending. 4 If the computer is running, shut it down. Turn off power to the computer and disconnect the power cord from the outlet. 5 Open the computer case according to the manufacturer's instructions. 6 Find the PCI slot you want to use for the serial ATA RAID Controller. Hint: Cable routing may be easier if you install the ATA RAID Controller next to an open slot. 7 Remove the metal filler bracket for the slot. Save this screw; it will be used to secure the serial ATA RAID Controller after you have seated it in the slot. Hint: While the ATA RAID Controller runs properly in any PCI or PCI-X slot, not all slots give equal performance due to the architecture of the PCI bus. In our laboratories, we have noticed that the slots closest to the Accelerated Graphics Port (AGP) or in the 64-bit PCI slot typically give the best performance. Our card should fit in both 32-bit and 64-bit PCI slots with 5V as well as with 3.3V. 8 Line up the ATA RAID Controller so that all pins make proper contact with the PCI slot pins when pushed into place. The Escalade ATA RAID Controller is keyed to ensure proper installation into a full-sized PCI slot. 9 Ensure that the contacts will mate with the grooves in the slot. Press down gently on the edge of the ATA RAID Controller directly above the slot until it is fully seated. 10 Check that the ATA RAID Controller's metal bracket covers the hole in the case and secure the bracket with the screw that was used to secure the filler bracket in step 4. Connect the drives to the interface cables Using native serial ATA drives 1 If your drives are not already installed in the computer chassis, install them now. Be sure that the drives are connected to the power supply. 22 3ware Escalade ATA RAID Controller User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
3ware Hardware Installation
22
3ware Escalade ATA RAID Controller User Guide
Note:
The connectors on the end of the controller are suscepti-
ble to damage from excessive bending.
4
If the computer is running, shut it down. Turn off power to the computer
and disconnect the power cord from the outlet.
5
Open the computer case according to the manufacturer’s instructions.
6
Find the PCI slot you want to use for the serial ATA RAID Controller.
Hint:
Cable routing may be easier if you install the ATA RAID
Controller next to an open slot.
7
Remove the metal filler bracket for the slot. Save this screw; it will be
used to secure the serial ATA RAID Controller after you have seated it in
the slot.
Hint:
While the ATA RAID Controller runs properly in any
PCI or PCI-X slot, not all slots give equal performance due to
the architecture of the PCI bus. In our laboratories, we have
noticed that the slots closest to the Accelerated Graphics Port
(AGP) or in the 64-bit PCI slot typically give the best perfor-
mance. Our card should fit in both 32-bit and 64-bit PCI slots
with 5V as well as with 3.3V.
8
Line up the ATA RAID Controller so that all pins make proper contact
with the PCI slot pins when pushed into place. The Escalade ATA RAID
Controller is keyed to ensure proper installation into a full-sized PCI slot.
9
Ensure that the contacts will mate with the grooves in the slot. Press down
gently on the edge of the ATA RAID Controller directly above the slot
until it is fully seated.
10
Check that the ATA RAID Controller’s metal bracket covers the hole in
the case and secure the bracket with the screw that was used to secure the
filler bracket in step 4.
Connect the drives to the interface cables
Using native serial ATA drives
1
If your drives are not already installed in the computer chassis, install
them now. Be sure that the drives are connected to the power supply.