ASRock 775Dual-915GV User Manual - Page 22

Onboard Headers and Connectors

Get ASRock 775Dual-915GV PDF manuals and user guides View all ASRock 775Dual-915GV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

2.9 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! FDD connector (33-pin FLOPPY1) (see p.12 No. 10) Pin1 FLOPPY1 the red-striped side to Pin1 Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. Primary IDE connector (Black) (39-pin IDE1, see p.12 No. 9) PIN1 IDE1 connect the blue end connect the black end to the motherboard to the IDE devices 80-conductor ATA 66/100 cable Note: Please refer to the instruction of your IDE device vendor for the details. Serial ATA Connectors (SATA1: see p.12 No. 14) (SATA2: see p.12 No. 13) (SATA3: see p.12 No. 12) (SATA4: see p.12 No. 11) SATA4 SATA3 These four Serial ATA (SATA) connectors support SATA data cables for internal storage devices. The current SATA interface allows up to 1.5 Gb/s data transfer rate. SATA2 SATA1 Serial ATA (SATA) Data Cable Either end of the SATA data cable can be connected to the SATA hard disk or the SATA connector on the motherboard. 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
22
22
22
22
22
FLOPPY1
Pin1
IDE1
PIN1
the red-striped side to Pin1
connect
the black end
to the IDE devices
connect the blue end
to the motherboard
80-conductor ATA 66/100 cable
2.9 Onboard Headers and Connectors
2.9 Onboard Headers and Connectors
2.9 Onboard Headers and Connectors
2.9 Onboard Headers and Connectors
2.9 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!
FDD connector
(33-pin FLOPPY1)
(see p.12
No. 10)
Note:
Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE connector (Black)
(39-pin IDE1, see p.12
No. 9)
Note:
Please refer to the instruction of your IDE device vendor for the details.
Serial ATA Connectors
These four Serial ATA (SATA)
(SATA1: see p.12
No. 14)
connectors support SATA data
(SATA2: see p.12 No. 13)
cables for internal storage
(SATA3: see p.12
No. 12)
devices. The current SATA
(SATA4: see p.12
No. 11)
interface allows up to 1.5 Gb/s
data transfer rate.
Serial ATA (SATA)
Either end of the SATA data cable
Data Cable
can be connected to the SATA
hard disk or the SATA connector
on the motherboard.
SATA1
SATA2
SATA3
SATA4