ASRock Fatal1ty Z97 Killer/3.1 User Manual - Page 30

Chassis and Power Fan, Besides four USB 3.0

Get ASRock Fatal1ty Z97 Killer/3.1 PDF manuals and user guides View all ASRock Fatal1ty Z97 Killer/3.1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

USB 3.0 Headers (19-pin USB3_4_5) (see p.6, No. 8) Vbus IntA_PA_SSRXIntA_PA_SSRX+ GND IntA_PA_SSTXIntA_PA_SSTX+ GND IntA_PA_DIntA_PA_D+ Vbus IntA_PB_SSRXIntA_PB_SSRX+ GND IntA_PB_SSTXIntA_PB_SSTX+ GND IntA_PB_DIntA_PB_D+ Dummy 1 Besides four USB 3.0 ports on the I/O panel, there is one header on this motherboard. Each USB 3.0 header can support two ports. Front Panel Audio Header (9-pin HD_AUDIO1) (see p.6, No. 21) GND PRESENCE# MIC_RET OUT_RET 1 OUT2_L J_SENSE OUT2_R MIC2_R MIC2_L his header is for connecting audio devices to the front audio panel. 1. High Deinition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instructions in our manual and chassis manual to install your system. 2. If you use an AC'97 audio panel, please install it to the front panel audio header by the steps below: A. Connect Mic_IN (MIC) to MIC2_L. B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L. C. Connect Ground (GND) to Ground (GND). D. MIC_RET and OUT_RET are for the HD audio panel only. You don't need to connect them for the AC'97 audio panel. E. To activate the front mic, go to the "FrontMic" Tab in the Realtek Control panel and adjust "Recording Volume". Chassis Speaker Header (4-pin SPEAKER1) (see p.6, No. 19) Chassis and Power Fan Connectors (4-pin CHA_FAN1) (see p.6, No. 12) (3-pin CHA_FAN2) (see p.6, No. 27) (3-pin CHA_FAN3) (see p.6, No. 26) 22 DUMMY SPEAKER 1 +5V DUMMY Please connect the chassis speaker to this header. GND +12V FAN_SPEED FAN_SPEED_CONTROL Please connect fan cables to the fan connectors and match the black wire to the ground pin. GND FAN_VOLTAGE FAN_SPEED English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
22
English
USB 3.0 ³eaders
(19-pin USB3_4_5)
(see p.6, No. 8)
Besides four USB 3.0
ports on the I/O panel,
there is one header on this
motherboard. Each USB
3.0 header can support
two ports.
Front Panel Audio ³eader
(9-pin ³D_AUDIO1)
(see p.6, No. 21)
His header is for
connecting audio devices
to the front audio panel.
Chassis Speaker ³eader
(4-pin SPEAKER1)
(see p.6, No. 19)
Please connect the chassis
speaker to this header.
Chassis and Power Fan
Connectors
(4-pin C³A_FAN1)
(see p.6, No. 12)
(3-pin C³A_FAN2)
(see p.6, No. 27)
(3-pin C³A_FAN3)
(see p.6, No. 26)
Please connect fan cables
to the fan connectors and
match the black wire to
the ground pin.
J_SENSE
OUT2_L
1
MIC_RET
PRESENCE#
GND
OUT2_R
MIC2_R
MIC2_L
OUT_RET
1.
´igh DeInition Audio supports Jack Sensing, but the panel wire on the chassis must
support ´DA to function correctly. Please follow the instructions in our manual and
chassis manual to install your system.
2. ±f you use an AC’97 audio panel, please install it to the front panel audio header by
the steps below:
A. Connect Mic_±N (M±C) to M±C2_L.
B. Connect Audio_R (R±N) to OU²2_R and Audio_L (L±N) to OU²2_L.
C. Connect Ground (GND) to Ground (GND).
D. M±C_RE² and OU²_RE² are for the ´D audio panel only. You don’t need to
connect them for the AC’97 audio panel.
E. ²o activate the front mic, go to the “FrontMic” ²ab in the Realtek Control panel
and adjust “Recording Volume”.
1
+5V
DUMMY
DUMMY
SPEAKER
FAN_SPEED
FAN_SPEED_CONTROL
+12V
GND
1
IntA_PB_D+
Dummy
IntA_PB_D-
GND
IntA_PB_SSTX+
GND
IntA_PB_SSTX-
IntA_PB_SSRX+
IntA_PB_SSRX-
Vbus
Vbus
Vbus
IntA_PA_SSRX-
IntA_PA_SSRX+
GND
IntA_PA_SSTX-
IntA_PA_SSTX+
GND
IntA_PA_D-
IntA_PA_D+
GND
FAN_VOLTAGE
FAN_SPEED