Acer P8800 User Manual - Page 22

USING THE PROJECTOR, Powering on / off the projector, Powering on / off, the projector

Get Acer P8800 PDF manuals and user guides View all Acer P8800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

USING THE PROJECTOR Powering on / off the projector On Off or Geometric Correction PIP/PBP F1 F2 Mode AV Mute On Off Geometric Correction PIP/PBP F1 Mode F2 AV Mute Info. Source ENTER ENTER Info. Source F3 Volume Re-Sync D Zoom Menu Format Freeze Remote ID All VGA S-Video HDMI1 HDMI2 123 HDBaseT Video DVI HDMI3 456 BNC YPbPr DisplayPort 3D 7890 Re-Sync F3 Powering on 1. Securely connect the power lead and signal/source cableV.olWumheen connectDeZdo,otmhe On/Standby LED will turn red. 2. Turn on the projector by pressing the " " either on the projector kMeeynpuad or the remote control. 3. A start up screen will display in approximately 10 seconds and the On/Standby LED will be flashing blue. Notee: The first time the projector is turned on, you will be promptedFtoormsaetlFercetezthee preRfeemrroeted language, projection orientation, and other settings. ID All Powering off VGA S-Video HDMI1 HDMI2 1. Turn off the projector by pressing the " " either on the pr1ojector2keypa3d or the remote control. 2. The following message will be displayed: Power Off HDBaseT Video DVI HDMI3 456 BNC YPbPr DisplayPort 3D Power Off? 7890 Press power key again. 3. Press the " " again to confirm, otherwise the message will disappear after 15 seconds. When you press the " " button for the second time, the projector will shut down. 4. The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the On/ Standby LED will flash blue. When the On/Standby LED turns solid red, this indicates the projector has entered standby mode. If you wish to turn the projector back on, you must wait until the cooling cycle has finished and the projector has entered standby mode. When the projector is in standby mode, simply press the " " button again to turn on the projector. 5. Disconnect the power lead from the electrical outlet and the projector. Notee: It is not recommended that the projector is turned on immediately, right after a power off procedure. 22 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
English
22
USING THE PROJECTOR
Powering on / off
the projector
On
Geometric
Mode
Correction
PIP/PBP
Off
F1
F2
AV Mute
ENTER
Source
Volume
D Zoom
Info.
F3
VGA
1
S-Video
2
HDMI1
3
HDMI2
HDMI3
Format
Freeze
Remote
ID
All
HDBaseT
4
Video
5
DVI
6
BNC
7
YPbPr
8
DisplayPort
9
3D
0
Re-Sync
Menu
On
Geometric
Correction
PIP/PBP
Off
or
Powering on
1.
Securely connect the power lead and signal/source cable. When connected, the On/Standby LED will
turn red.
2.
Turn on the projector by pressing the "
" either on the projector keypad or the remote control.
3.
A start up screen will display in approximately 10 seconds and the On/Standby LED will be flashing
blue.
Note°
The first time the projector is turned on, you will be prompted to select the preferred language, projection
orientation, and other settings.
Powering off
1.
Turn off
the projector by pressing the
"
" either on the projector keypad or the remote control.
2.
The following message will be displayed:
Power Off
Power Off?
Press power key again.
3.
Press the "
"
again to confirm, otherwise the message will disappear after 15 seconds. When you
press the "
" button for the second time, the projector will shut down.
4.
The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the On/
Standby LED will flash blue. When the On/Standby LED turns solid red, this indicates the projector has
entered standby mode. If you wish to turn the projector back on, you must wait until the cooling cycle
has finished and the projector has entered standby mode. When the projector is in standby mode,
simply press the "
" button again to turn on the projector.
5.
Disconnect the power lead from the electrical outlet and the projector.
Note°
It is not recommended that the projector is turned on immediately, right after a power off
procedure.