Acer UL6500 User Manual - Page 30

Auto Power Off, Quick Cooling, Standby Settings, Network Settings, Light Source Hours, LAN Control

Get Acer UL6500 PDF manuals and user guides View all Acer UL6500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

• On: Approx. 80% Note • When "Eco Mode" is set to "On", the fan sound and power consumption are lower than they are when "Off" is selected. (Projection brightness decreases.) Light Source Hours You can confirm the cumulative usage time. Auto Power Off • Disable: The Auto Power Off function will be disabled. • 10 Min./20 Min./30 Min.: When no input signal is detected for more than selected time, the projector will automatically enter Standby mode. Note • When the Auto Power Off function is set to other than "Disable", 30 seconds before the projector enters Standby mode, the message will appear on the screen Quick Cooling This function changes the cooling time. • Off: The cooling time will be normal time. • On: The cooling time is reduced. Standby Settings This function is setting power consumption reduction in standby mode. LAN Control You can be used Network function in Standby mode. • Off: Network functions are switched off in Standby mode. • On: Network functions are activated even if the projector is in Standby mode. Network Settings Allow you to configure the wired LAN settings. Refer to "Setting up the Projector Network Environment" on page 33. DHCP Client Connect the LAN cable before turning the projector on. If not, the DHCP Client function does not work. • On: Obtains configuration parameters for TCP/IP network automatically. • Off: Sets the TCP/IP manually. When "DHCP Client" is set to "On", Select "Save Settings", then press ENTER. IP Address Factory default setting: 0. 0. 0. 0 Enter an IP address appropriate for the network. Subnet Mask Factory default setting: 0. 0. 0. 0 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
29
• On: Approx. 80%
Note
•
When “Eco Mode” is set to “On”, the fan sound and power consumption are lower than
they are when “Off” is selected. (Projection brightness decreases.)
Light Source Hours
You can confirm the cumulative usage time.
Auto Power Off
• Disable: The Auto Power Off function will be disabled.
•
10 Min./20 Min./30 Min.: When no input signal is detected for more than selected
time, the projector will automatically enter Standby mode.
Note
•
When the Auto Power Off function is set to other than “Disable”, 30 seconds before the
projector enters Standby mode, the message will appear on the screen
Quick Cooling
This function changes the cooling time.
• Off: The cooling time will be normal time.
• On: The cooling time is reduced.
Standby Settings
This function is setting power consumption reduction in standby mode.
LAN Control
You can be used Network function in Standby mode.
• Off: Network functions are switched off in Standby mode.
•
On: Network functions are activated even if the projector is in Standby mode.
Network Settings
Allow you to configure the wired LAN settings. Refer to
"Setting up the Projector
Network Environment" on page 33
.
DHCP Client
Connect the LAN cable before turning the projector on. If not, the DHCP Client
function does not work.
• On: Obtains configuration parameters for TCP/IP network automatically.
• Off: Sets the TCP/IP manually.
When "
DHCP Client
" is set to "
On
", Select "
Save Settings
", then press
ENTER
.
IP Address
Factory default setting: 0. 0. 0. 0
Enter an IP address appropriate for the network.
Subnet Mask
Factory default setting: 0. 0. 0. 0