Adaptec 2045 User Manual and Install Guide - Page 45

Attach the low-profile bracket to the controller board. The low-profile bracket is installed

Get Adaptec 2045 PDF manuals and user guides View all Adaptec 2045 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Chapter 4: Getting Started ● 44 To replace the full-height bracket with the low-profile bracket: 1 Remove the full-height bracket from the controller board. The full-height bracket is installed on the front side of the controller, with the mounting screws inserted from the back of the controller, as shown in the Figure 1. Using a Phillips head screw driver, remove the mounting screws, as shown in Figure 2, then set the screws aside for use in Step 2. Remove mounting screws with Phillips screw driver Back of board Front of board Figure 1 Figure 2 2 Attach the low-profile bracket to the controller board. The low-profile bracket is installed on the back side of the controller, with the mounting screws inserted from the front of the controller, as shown the Figure 3. Insert the screws through the holes on the front of the controller, then fasten the screws to the bracket with a Phillips screw driver. ! Caution: The mount points on the low-profile bracket have a smooth or flat side and a raised side that looks like a spacer (see Figure 3). Be sure to install the bracket with the flat side against the controller PCB and the raised side facing away from the PCB. Flat side of bracket Front of board Back of board Raised side of bracket Figure 3 ! Caution: The torque on the mounting screws should be a maximum of 3.0-4.0 lbf-in to avoid deformation. Be sure that the controller is not bent after attaching the low-profile bracket to the controller board.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
Chapter 4: Getting Started
●
44
To replace the full-height bracket with the low-profile bracket:
1
Remove the full-height bracket from the controller board. The full-height bracket is
installed on the front side of the controller, with the mounting screws inserted from the
back of the controller, as shown in the Figure 1. Using a Phillips head screw driver, remove
the mounting screws, as shown in Figure 2, then set the screws aside for use in
Step 2
.
2
Attach the low-profile bracket to the controller board. The low-profile bracket is installed
on the
back
side of the controller, with the mounting screws inserted from the front of the
controller, as shown the Figure 3.
Insert the screws through the holes on the front of the controller, then fasten the screws to
the bracket with a Phillips screw driver.
Caution:
The mount points on the low-profile bracket have a smooth or flat side and a
raised side that looks like a spacer (see Figure 3). Be sure to install the bracket with
the flat side against the controller PCB and the raised side facing away from the PCB.
Caution:
The torque on the mounting screws should be a maximum of 3.0-4.0 lbf-in to
avoid deformation. Be sure that the controller is not bent after attaching the low-profile
bracket to the controller board.
Back of board
Remove mounting
screws with Phillips
screw driver
Front of board
Figure 1
Figure 2
!
Back of board
Front of board
Flat side of bracket
Figure 3
Raised side of bracket
!