Adaptec 2170200 User Guide - Page 36

Choosing a RAID Level, Choosing Installation Options, Basic Installation Steps

Get Adaptec 2170200 PDF manuals and user guides View all Adaptec 2170200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Chapter 5: Getting Started l 36 Choosing a RAID Level Your HostRAID controller supports these RAID levels. RAID 0 (Non-redundant Array)-Stripes data across multiple disk drives. Improved performance but no redundancy. RAID 1 Array-Created from two disk drives where one disk drive is a mirror of the other (the same data is stored on each disk drive). Redundancy but reduced capacity. RAID 10 Array-Built from two or more equal-sized RAID 1 arrays, stripes and mirrors data across multiple disk drives. Redundancy and improved performance. See page 64 for more information on RAID levels and use the table on page 65 to see how many disk drives you must connect to your HostRAID controller to support the RAID level you want. Choosing Installation Options When you install your HostRAID controller, you can choose to create a bootable array and then install both operating system and controller driver on that array. Alternatively, you can complete a standard installation, where you install the controller driver on an existing operating system. Note: Adaptec 1225SA controller does not support bootable devices, hence install this controller only on an existing operating system. Basic Installation Steps This section describes the installation process. Follow the steps for the installation option you've chosen. Installing with an Operating System You can install your HostRAID controller and the operating system using these steps: 1 Install and connect your controller and disk drives (see page 26). 2 Set the boot controller (see page 38). 3 Make the array bootable (see page 41). 4 Install your operating system and the driver (see page 42). 5 Install Adaptec Storage Manager and begin to manage your data storage (see page 50). Installing with an Operating System On a Bootable Disk Drive/Array When you install your HostRAID controller, you can create a bootable disk drive or an array and then install both operating system and controller driver on that disk drive or array. Alternatively, you can perform the standard installation, and install the controller driver on an existing operating system

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
Chapter 5: Getting Started
l 36
Choosing a RAID Level
Your HostRAID controller supports these RAID levels.
RAID 0 (Non-redundant Array)
—Stripes data across multiple disk drives. Improved
performance but no redundancy.
RAID 1 Array
—Created from two disk drives where one disk drive is a mirror of the other (the
same data is stored on each disk drive). Redundancy but reduced capacity.
RAID 10 Array
—Built from two or more equal-sized RAID 1 arrays, stripes and mirrors data
across multiple disk drives. Redundancy and improved performance.
See
page 64
for more information on RAID levels and use the table on
page 65
to see how many
disk drives you must connect to your HostRAID controller to support the RAID level you
want.
Choosing Installation Options
When you install your HostRAID controller, you can choose to create a bootable array and
then install both operating system and controller driver on that array. Alternatively, you can
complete a standard installation, where you install the controller driver on an existing
operating system.
Note:
Adaptec 1225SA controller does not support bootable devices, hence install this controller
only on an existing operating system.
Basic Installation Steps
This section describes the installation process. Follow the steps for the installation option
you’ve chosen.
Installing with an Operating System
You can install your HostRAID controller and the operating system using these steps:
1
Install and connect your controller and disk drives (see
page 26
).
2
Set the boot controller (see
page 38
).
3
Make the array bootable (see
page 41
).
4
Install your operating system and the driver (see
page 42
).
5
Install Adaptec Storage Manager and begin to manage your data storage (see
page 50
).
Installing with an Operating System On a Bootable Disk Drive/Array
When you install your HostRAID controller, you can create a bootable disk drive or an array
and then install both operating system and controller driver on that disk drive or array.
Alternatively, you can perform the standard installation, and install the controller driver on an
existing operating system