Adaptec P2280A User Guide - Page 15

Completing a Fresh Windows NT 4.0 Installation From CD-ROM

Get Adaptec P2280A - Storage Controller U160 SCSI 160 MBps PDF manuals and user guides View all Adaptec P2280A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Microsoft Windows NT Installation Completing a Fresh Windows NT 4.0 Installation From CD-ROM 1 Insert the Windows NT 4.0 CD into the CD-ROM drive. 2 Start your system. Press the F6 key when you see the following message: "Setup is inspecting your computer's hardware configuration..." If you do not see this message, your system may not be setup to boot from a CD-ROM. You will need to install from floppy disks. See Completing a Fresh Windows NT 4.0 Installation From Floppy Disk on page 2-2. 3 When prompted, press S to specify an additional device. 4 Press Enter to select Others; insert the Ultra160 Family Manager Set disk for Windows in your floppy disk drive. 5 Using the arrow keys, select the following driver and press Enter: Adaptec Ultra160 Family PCI SCSI Controller (NT4.0) 6 To add other host adapters that are not part of the Ultra160 Family, press S and repeat from Step 4 for each additional adapter and insert the appropriate driver disk. The Adaptec Ultra160 Family host adapters use the same driver; it is not necessary to install the driver again. 7 Press Enter to continue with the Windows NT operating system setup. Follow the instructions on-screen and in the Windows NT documentation to complete the installation. 2-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
2-3
Microsoft Windows NT Installation
Completing a Fresh Windows NT 4.0 Installation
From CD-ROM
1
Insert the Windows NT 4.0 CD into the CD-ROM drive.
2
Start your system. Press the
F6
key when you see the following
message: “
Setup is inspecting your computer’s hardware
configuration...”
If you do not see this message, your system may not be setup
to boot from a CD-ROM. You will need to install from floppy
disks. See
Completing a Fresh Windows NT 4.0 Installation From
Floppy Disk
on page 2-2.
3
When prompted, press
S
to specify an additional device.
4
Press
Enter
to select
Others;
insert the Ultra160 Family
Manager Set disk for Windows in your floppy disk drive.
5
Using the arrow keys, select the following driver and press
Enter
:
Adaptec Ultra160 Family PCI SCSI Controller (NT4.0)
6
To add other host adapters that are not part of the Ultra160
Family, press
S
and repeat from Step 4 for each additional
adapter and insert the appropriate driver disk. The Adaptec
Ultra160 Family host adapters use the same driver; it is not
necessary to install the driver again.
7
Press
Enter
to continue with the Windows NT operating
system setup. Follow the instructions on-screen and in the
Windows NT documentation to complete the installation.