Adaptec P2280A User Guide - Page 71

The host adapter may have reset the SCSI bus. This is a normal

Get Adaptec P2280A - Storage Controller U160 SCSI 160 MBps PDF manuals and user guides View all Adaptec P2280A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

UnixWare Installation [xxxxx096] Adapter hardware initialization failure - possible resource conflict The driver has attempted to initialize the adapter hardware but failed. This might suggest that the adapter resources (e.g., IRQ) conflict with another board installed in your system. [xxxxx097] Unable to allocate memory This indicates that there may be a problem with the amount of memory installed in your system. Verify that your system has at least the minimum amount of memory required by your operating system. [xxxxx098] Exceeded maximum number of host bus adapters The driver has detected more host bus adapters than is supported by this version of the driver or operating system. [xxxxx0a4] SCSI bus reset by third party Hardware such as an array enclosure may have reset the SCSI bus. This is a normal condition unless you receive additional errors. [xxxxx0a5] SCSI bus reset by host adapter The host adapter may have reset the SCSI bus. This is a normal condition unless you receive additional errors. [xxxxx0cf] System configuration error The driver encountered an error with your hardware. Refer to your host adapter's user's guide for troubleshooting information. [xxxxx0d0] Command timeout The target device is either busy, not ready, malfunctioning, or is not present. Refer to your host adapter's user's guide for troubleshooting information. [xxxxx0d7] Target device scan failed The driver encountered an error scanning the target device. Refer to your host adapter's user's guide for troubleshooting information. Ì 5-13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
5-13
UnixWare Installation
[xxxxx096] Adapter hardware initialization failure - possible resource conflict
The driver has attempted to initialize the adapter hardware but
failed. This might suggest that the adapter resources (e.g., IRQ)
conflict with another board installed in your system.
[xxxxx097] Unable to allocate memory
This indicates that there may be a problem with the amount of
memory installed in your system. Verify that your system has at
least the minimum amount of memory required by your operating
system.
[xxxxx098] Exceeded maximum number of host bus adapters
The driver has detected more host bus adapters than is supported by
this version of the driver or operating system.
[xxxxx0a4] SCSI bus reset by third party
Hardware such as an array enclosure may have reset the SCSI bus.
This is a normal condition unless you receive additional errors.
[xxxxx0a5] SCSI bus reset by host adapter
The host adapter may have reset the SCSI bus. This is a normal
condition unless you receive additional errors.
[xxxxx0cf] System configuration error
The driver encountered an error with your hardware. Refer to your
host adapter’s user’s guide for troubleshooting information.
[xxxxx0d0] Command timeout
The target device is either busy, not ready, malfunctioning, or is not
present. Refer to your host adapter’s user’s guide for
troubleshooting information.
[xxxxx0d7] Target device scan failed
The driver encountered an error scanning the target device. Refer to
your host adapter’s user’s guide for troubleshooting information.