Home » Asus Manuals » Motherboards » Asus AT4NM10-I » Manual Viewer

Asus AT4NM10-I User Manual - Page 22

AT4NM10-I SATA connectors

Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

AT4NM10-I 2. Serial ATA connectors (7-pin SATA1, SATA2) These connectors are for the Serial ATA signal cables for Serial ATA 3Gb/s hard disk drives and optical disk drives. The Serial ATA 3Gb/s is backward compatible with the Serial ATA 1.5Gb/s specification. The data transfer rate of the Serial ATA 3Gb/s is faster than the standard parallel ATA (133 MB/s). AT4NM10-I SATA connectors Install the Windows® XP Service Pack 2 or later versions before using Serial ATA. 3. USB connectors (10-1 pin USB56, USB78) These connectors are for USB 2.0 ports. Connect the USB module cable to this connector, then install the module to a slot opening at the back of the system chassis. This USB connector complys with USB 2.0 specification that supports up to 480 Mbps connection speed. AT4NM10-I AT4NM10-I USB2.0 connectors Never connect a 1394 cable to the USB connector. Doing so will damage the motherboard! The USB module cable is purchased separately. 1-13 Chapter 1: Product introduction

Section	Page
Notices	5
Safety information	6
About this guide	6
AT4NM10-I specifications summary	8
Chapter 1	10
Product introduction	10
1.1 Before you proceed	10
1.2 Motherboard overview	11
1.2.1 Motherboard layout	11
1.2.2 Layout contents	11
1.3 Central Processing Unit (CPU)	12
1.4 System memory	12
1.4.1 Overview	12
1.4.2 Memory configurations	13
1.5 Expansion slot	17
1.5.1 Installing an expansion card	17
1.5.2 Configuring an expansion card	17
1.5.3 PCI slot	17
1.6 Jumpers	18
1.7 Connectors	20
1.7.1 Rear panel connectors	20
1.7.2 Internal connectors	21
1.8 Software support	27
1.8.1 Installing an operating system	27
1.8.2 Support DVD information	27
Chapter 2	28
BIOS information	28
2.1 Managing and updating your BIOS	28
2.1.1 ASUS Update utility	28
2.1.2 ASUS EZ Flash 2	29
2.1.3 ASUS CrashFree BIOS	30
2.2 BIOS setup program	31
2.3 Main menu	31
2.3.1 System Time	32
2.3.2 System Date	32
2.3.3 SATA 1/2	32
2.3.4 Storage Configuration	33
2.3.5 System Information	33
2.4 Advanced menu	33
2.4.1 CPU Configuration	34
2.4.2 Chipset	34
2.4.3 Onboard Devices Configuration	35
2.4.4 USB Configuration	36
2.4.5 PCI PnP	37
2.5 Power menu	37
2.5.1 Suspend Mode	37
2.5.2 ACPI 2.0 Support	37
2.5.3 ACPI APIC Support	37
2.5.4 Control EuP	38
2.5.5 APM Configuration	38
2.5.6 Hardware Monitor	38
2.6 Boot menu	39
2.6.1 Boot Device Priority	39
2.6.2 Boot Settings Configuration	39
2.6.3 Security	40
2.7 Tools menu	41
2.7.1 ASUS EZ Flash 2	41
2.7.2 Express Gate	41
2.7.3 AI NET 2	42

Match case Limit results 1 per page

1-13

Chapter 1: Product introduction

Serial ATA connectors (7-pin SATA1, SATA2)

These connectors are for the Serial ATA signal cables for Serial ATA 3Gb/s hard disk

drives and optical disk drives. The Serial ATA 3Gb/s is backward compatible with the

Serial ATA 1.5Gb/s speciﬁcation. The data transfer rate of the Serial ATA 3Gb/s is faster

than the standard parallel ATA (133 MB/s).

AT4NM10-I

AT4NM10-I SATA connectors

Install the Windows

XP Service Pack 2 or later versions before using Serial ATA.

USB connectors (10-1 pin USB56, USB78)

These connectors are for USB 2.0 ports. Connect the USB module cable to this

connector, then install the module to a slot opening at the back of the system chassis.

This USB connector complys with USB 2.0 speciﬁcation that supports up to 480 Mbps

connection speed.

AT4NM10-I

AT4NM10-I USB2.0 connectors

Never connect a 1394 cable to the USB connector. Doing so will damage the motherboard!

The USB module cable is purchased separately.