Home » Asus Manuals » Motherboards » Asus AT4NM10-I » Manual Viewer

Asus AT4NM10-I User Manual - Page 23

AT4NM10-I Internal speaker connector

Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

AT4NM10-I 4. Chassis intrusion connector (4-1 pin CHASSIS) This connector is for a chassis-mounted intrusion detection sensor or switch. Connect one end of the chassis intrusion sensor or switch cable to this connector. The chassis intrusion sensor or switch sends a high-level signal to this connector when a chassis component is removed or replaced. The signal is then generated as a chassis intrusion event. By default, the pin labeled "Chassis Signal" and "Ground" are shorted with a jumper cap. Remove the jumper caps only when you intend to use the chassis intrusion detection feature. AT4NM10-I Chassis intrusion connector 5. Internal speaker connector (4-pin SPEAKER) The 4-pin connector is for the chassis-mounted system warning speaker. The speaker allows you to hear system beeps and warnings. AT4NM10-I Internal speaker connector AT4NM10-I ASUS AT4NM10-I 1-14

Section	Page
Notices	5
Safety information	6
About this guide	6
AT4NM10-I specifications summary	8
Chapter 1	10
Product introduction	10
1.1 Before you proceed	10
1.2 Motherboard overview	11
1.2.1 Motherboard layout	11
1.2.2 Layout contents	11
1.3 Central Processing Unit (CPU)	12
1.4 System memory	12
1.4.1 Overview	12
1.4.2 Memory configurations	13
1.5 Expansion slot	17
1.5.1 Installing an expansion card	17
1.5.2 Configuring an expansion card	17
1.5.3 PCI slot	17
1.6 Jumpers	18
1.7 Connectors	20
1.7.1 Rear panel connectors	20
1.7.2 Internal connectors	21
1.8 Software support	27
1.8.1 Installing an operating system	27
1.8.2 Support DVD information	27
Chapter 2	28
BIOS information	28
2.1 Managing and updating your BIOS	28
2.1.1 ASUS Update utility	28
2.1.2 ASUS EZ Flash 2	29
2.1.3 ASUS CrashFree BIOS	30
2.2 BIOS setup program	31
2.3 Main menu	31
2.3.1 System Time	32
2.3.2 System Date	32
2.3.3 SATA 1/2	32
2.3.4 Storage Configuration	33
2.3.5 System Information	33
2.4 Advanced menu	33
2.4.1 CPU Configuration	34
2.4.2 Chipset	34
2.4.3 Onboard Devices Configuration	35
2.4.4 USB Configuration	36
2.4.5 PCI PnP	37
2.5 Power menu	37
2.5.1 Suspend Mode	37
2.5.2 ACPI 2.0 Support	37
2.5.3 ACPI APIC Support	37
2.5.4 Control EuP	38
2.5.5 APM Configuration	38
2.5.6 Hardware Monitor	38
2.6 Boot menu	39
2.6.1 Boot Device Priority	39
2.6.2 Boot Settings Configuration	39
2.6.3 Security	40
2.7 Tools menu	41
2.7.1 ASUS EZ Flash 2	41
2.7.2 Express Gate	41
2.7.3 AI NET 2	42

Match case Limit results 1 per page

ASUS AT4NM10-I

1-14

Chassis intrusion connector (4-1 pin CHASSIS)

This connector is for a chassis-mounted intrusion detection sensor or switch. Connect

one end of the chassis intrusion sensor or switch cable to this connector. The chassis

intrusion sensor or switch sends a high-level signal to this connector when a chassis

component is removed or replaced. The signal is then generated as a chassis intrusion

event.

By default, the pin labeled “Chassis Signal” and “Ground” are shorted with a jumper

cap. Remove the jumper caps only when you intend to use the chassis intrusion

detection feature.

AT4NM10-I Chassis intrusion connector

AT4NM10-I

Internal speaker connector (4-pin SPEAKER)

The 4-pin connector is for the chassis-mounted system warning speaker. The speaker

allows you to hear system beeps and warnings.

AT4NM10-I

AT4NM10-I Internal speaker connector