Asus H110M-PLUS H110M-PLUS Users manual English - Page 11

H110 Serial ATA 6.0Gb/s connectors 7-pin SATA6G_1~4, Clear RTC RAM 2-pin CLRTC

Get Asus H110M-PLUS PDF manuals and user guides View all Asus H110M-PLUS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Intel® H110 Serial ATA 6.0Gb/s connectors (7-pin SATA6G_1~4) These connectors connect to Serial ATA 6.0 Gb/s hard disk drives via Serial ATA 6.0 Gb/s signal cables. When using hot-plug and NCQ, set the SATA Mode Selection item in the BIOS to [AHCI]. USB 3.0 connectors (20-1 pin USB3_12) Connect a USB 3.0 module to any of these connectors for additional USB 3.0 front or rear panel ports. These connectors comply with USB 3.0 specifications and provide faster data transfer speeds of up to 5 Gbps, faster charging time for USBchargeable devices, optimized power efficiency, and backward compatibility with USB 2.0. Clear RTC RAM (2-pin CLRTC) This header allows you to clear the CMOS RTC RAM data of the system setup information such as date, time, and system passwords. To erase the RTC RAM: CLRTC +3V_BAT GND 1. Turn OFF the computer and unplug the power cord. 2. Use a metal object such as a screwdriver to short the two pins. PIN 1 3. Plug the power cord and turn ON the computer. 4. Hold down the key during the boot process and enter BIOS setup to re-enter data. If the steps above do not help, remove the onboard battery and short the two pins again to clear the CMOS RTC RAM data. After clearing the CMOS, reinstall the battery. USB 2.0 connectors (10-1 pin USB1112, USB1314) Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0 specifications and supports up to 480Mbps connection speed. +5V SPDIFOUT GND Digital audio connector (4-1 pin SPDIF_OUT) Connect the S/PDIF Out module cable to this connector, then install the module to a slot opening at the back of the system chassis. Front panel audio connector (10-1 pin AAFP) PIN 1 SPDIF_OUT This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC`97 audio standard. Connect one end of the front panel audio I/O module cable to this connector. ASUS H110M-PLUS 1-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
ASUS H110M-PLUS
1-3
Intel
®
H110 Serial ATA 6.0Gb/s connectors (7-pin SATA6G_1~4)
These connectors connect to Serial ATA 6.0 Gb/s hard disk drives via Serial ATA
6.0 Gb/s signal cables.
When using hot-plug and NCQ, set the
SATA Mode Selection
item in the BIOS to
[AHCI].
USB 3.0 connectors (20-1 pin USB3_12)
Connect a USB 3.0 module to any of these connectors for additional USB 3.0 front
or rear panel ports. These connectors comply with USB 3.0 specifications and
provide faster data transfer speeds of up to 5 Gbps, faster charging time for USB-
chargeable devices, optimized power efficiency, and backward compatibility with
USB 2.0.
Clear RTC RAM (2-pin CLRTC)
This header allows you to clear the CMOS RTC RAM data of the system setup
information such as date, time, and system passwords.
To erase the RTC RAM:
1.
Turn OFF the computer and unplug the power cord.
2.
Use a metal object such as a screwdriver to short the two pins.
3.
Plug the power cord and turn ON the computer.
4.
Hold down the <
Del
> key during the boot process and enter BIOS setup to
re-enter data.
If the steps above do not help, remove the onboard battery and short the
two pins again to clear the CMOS RTC RAM data. After clearing the CMOS,
reinstall the battery.
USB 2.0 connectors (10-1 pin USB1112, USB1314)
Connect the USB module cable to any of these connectors, then install the module
to a slot opening at the back of the system chassis. These USB connectors comply
with USB 2.0 specifications and supports up to 480Mbps connection speed.
Digital audio connector (4-1 pin SPDIF_OUT)
Connect the S/PDIF Out module cable to this connector, then
install the module to a slot opening at the back of the system
chassis.
Front panel audio connector (10-1 pin AAFP)
This connector is for a chassis-mounted front panel audio I/O module that supports
either HD Audio or legacy AC`97 audio standard. Connect one end of the front
panel audio I/O module cable to this connector.
CLRTC
+3V_BAT
GND
PIN 1
SPDIF_OUT
+5V
SPDIFOUT
GND
PIN 1