Asus P I-XP55TVP4 User Manual - Page 29

Asus P I-XP55TVP4 Manual

Page 29 highlights

III. INSTALLATION 11. Turbo LED Lead (PANEL) The motherboard's turbo function is always on. The turbo LED connection is labeled here but the LED will remain constantly lit while the system power is on. This lead should be connected to the Power LED on the system cabinet if your keyboard plug does not have a power LED lead. See the figure below. 12. SMI Suspend Switch Lead (PANEL) This allows the user to manually place the system into a suspend mode or "Green" mode where system activity will be instantly decreased to save electricity and expand the life of certain components when the system is not in use. This 2-pin connector (see the figure below) connects to the cabinet-mounted suspend switch. If you do not have a switch for the connector, you may use the "Turbo Switch" since it does not have a function. SMI is activated when it detects a short to open moment and therefore leaving it shorted will not cause any problems. May require one or two pushes depending on the position of the switch. Wake-up can be controlled by settings in the BIOS but the keyboard will always allow wakeup (the SMI lead cannot wake-up the system). If you want to use this connector, "Suspend Switch" in the Power Management Setup of the BIOS SOFTWARE section should be on the default setting of Enable. 13. Reset Switch Lead (PANEL) This 2-pin connector connects to the cabinet-mounted reset switch for rebooting your computer without having to turn off your power switch This is a preferred method of rebooting in order to prolong the life of the system's power supply. See the figure below. 14. Keyboard Lock Switch Lead & System Power LED (PANEL) This 5-pin connector connects to the cabinet-mounted keyboard lock switch for locking the keyboard and also to connect the system power LED. The system power LED lights when the system is powered on. See the figure below. 15. Speaker Connector (PANEL) This 4-pin connector connects to the cabinet-mounted speaker. PANEL +5V NC GND LOCK GND +5V GND GND SPKR Turbo LED SMI Lead ATX Power Switch Reset SW +5V GND GND GND System Power LED Keyboard Lock Speaker Connector GND System Panel Connections ASUS P/I-XP55TVP4 User's Manual 23 III. INSTALLATION (Connectors)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32

ASUS P/I-XP55TVP4 User’s Manual
23
III. INSTALLATION
11.
Turbo LED Lead (PANEL)
The motherboard's turbo function is always on.
The turbo LED connection is
labeled here but the LED will remain constantly lit while the system power is
on.
This lead should be connected to the Power LED on the system cabinet if
your keyboard plug does not have a power LED lead.
See the figure below.
12. SMI Suspend Switch Lead (PANEL)
This allows the user to manually place the system into a suspend mode or "Green"
mode where system activity will be instantly decreased to save electricity and
expand the life of certain components when the system is not in use.
This 2-pin
connector (see the figure below) connects to the cabinet-mounted suspend switch.
If you do not have a switch for the connector, you may use the "Turbo Switch"
since it does not have a function.
SMI is activated when it detects a
short to
open
moment and therefore leaving it shorted will not cause any problems.
May
require one or two pushes depending on the position of the switch.
Wake-up can
be controlled by settings in the BIOS but the keyboard will always allow wake-
up (the SMI lead cannot wake-up the system).
If you want to use this connector,
"Suspend Switch" in the
Power Management Setup
of the BIOS SOFTWARE
section should be on the default setting of
Enable.
13. Reset Switch Lead (PANEL)
This 2-pin connector connects to the cabinet-mounted reset switch for rebooting
your computer without having to turn off your power switch
This is a preferred
method of rebooting in order to prolong the life of the system's power supply.
See the figure below.
14. Keyboard Lock Switch Lead & System Power LED (PANEL)
This 5-pin connector connects to the cabinet-mounted keyboard lock switch for
locking the keyboard and also to connect the system power LED.
The system
power LED lights when the system is powered on.
See the figure below.
15. Speaker Connector (PANEL)
This 4-pin connector connects to the cabinet-mounted speaker.
System Panel Connections
+5V
NC
GND
LOCK
GND
+5V
SPKR
Speaker
Connector
GND
GND
GND
+5V
Reset SW
SMI Lead
Turbo LED
ATX Power
Switch
System
Power LED
Keyboard Lock
GND
GND
GND
PANEL
(Connectors)
III.
INSTALLATION