Asus P2L-B User Manual - Page 28

IDE activity LED IDE LED, 2 pins

Get Asus P2L-B PDF manuals and user guides View all Asus P2L-B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

III. INSTALLATION (Connectors) III. INSTALLATION 5. Primary / Secondary IDE connectors (IDE, two 40-1 pins) These connectors support the provided IDE hard disk ribbon cable. After connecting the single end to the board, connect the two plugs at the other end to your hard disk(s). If you install two hard disks, you must set the second drive to Slave mode. Refer to the documentation of your hard disk for the jumper settings. BIOS now supports SCSI device or IDE CD-ROM bootup (see HDD Sequence SCSI/IDE First & Boot Sequence in the BIOS Features Setup of the BIOS SOFTWARE) (Pin 20 is removed to prevent inserting in the wrong orientation when using ribbon cables with pin 20 plugged). Pin 1 R Secondary IDE Connector Primary IDE Connector P2L-B IDE Connectors TIP: You may configure two hard disks to be both Masters using one ribbon cable on the primary IDE connector and another ribbon cable on the secondary IDE connector. You may install one operating system on an IDE drive and another on a SCSI drive and select the boot disk through BIOS Features Setup. 6. IDE activity LED (IDE LED, 2 pins) This connector supplies power to the cabinet's IDE activity LED. Read and write activity by devices connected to the Primary or Secondary IDE connectors will cause the LED to light up. TIP: If the case-mounted LED does not light, try reversing the 2-pin plug. R P2L-B IDE Activity LED IDE_LED 28 ASUS P2L-B User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
28
ASUS P2L-B User’s Manual
III. INSTALLATION
(Connectors)
III.
INSTALLATION
5.
Primary / Secondary IDE connectors
(IDE, two 40-1 pins)
These connectors support the provided IDE hard disk ribbon cable. After con-
necting the single end to the board, connect the two plugs at the other end to
your hard disk(s). If you install two hard disks, you must set the second drive to
Slave mode. Refer to the documentation of your hard disk for the jumper set-
tings. BIOS now supports SCSI device or IDE CD-ROM bootup (see
HDD Se-
quence SCSI/IDE First
&
Boot Sequence
in the
BIOS Features Setup
of the
BIOS SOFTWARE)
(Pin 20 is removed to prevent inserting in the wrong
orientation when using ribbon cables with pin 20 plugged).
P2L-B IDE Connectors
Primary IDE Connector
Secondary IDE Connector
Pin 1
TIP:
You may configure two hard disks to be both Masters using one ribbon
cable on the primary IDE connector and another ribbon cable on the secondary
IDE connector.
You may install one operating system on an IDE drive and
another on a SCSI drive and select the boot disk through BIOS Features Setup.
6.
IDE activity LED (IDE LED, 2 pins)
This connector supplies power to the cabinet’s IDE activity LED.
Read and
write activity by devices connected to the Primary or Secondary IDE connectors
will cause the LED to light up.
P2L-B IDE Activity LED
TIP:
If the case-mounted LED does not light,
try reversing the 2-pin plug.
IDE_LED