Asus Q170T/CSM User Guide - Page 11

Internal DC power connector 2-pin ATX19V/12V

Get Asus Q170T/CSM PDF manuals and user guides View all Asus Q170T/CSM manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Internal DC power connector (2-pin ATX19V/12V) This connector is for an ATX power supply. The plug from the power supply is designed to fit this connector in only one orientation. Find the proper orientation and push down firmly until the connector completely fits. ATX19V/12V GND PIN 1 DC_JACK_IN CPU and chassis fan connectors (4-pin CPU_FAN, 4-pin CHA_FAN ) Connect the fan cables to the fan connectors on the motherboard, ensuring that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. These are not jumpers! Do not place jumper caps on the fan connectors! The CPU_FAN connector supports a CPU fan of maximum 1A (12 W) fan power. Serial ATA 6.0Gb/s connectors (SATA6G_3~6) These connectors connect to Serial ATA 6.0 Gb/s hard disk drives via Serial ATA 6.0 Gb/s signal cables. USB 3.0 connector (20-1 pin USB3_12) Connect a USB 3.0 module to this connector for additional USB 3.0 front or rear panel ports. This connector complies with USB 3.0 specifications and provides faster data transfer speeds of up to 5 Gbps, faster charging time for USBchargeable devices, optimized power efficiency, and backward compatibility with USB 2.0. DDR4 SO-DIMM slots Install 2 GB, 4 GB, 8 GB, and 16 GB non-ECC un-buffered DDR4 SO-DIMMs into these DIMM sockets. SATA power connector (15-pin SATA_PWRCON) This connector is for the SATA power cable. The power cable plug is designed to fit this connector in only one orientation. Find the proper orientation and push down firmly until the connector completely fit. To provide power to your SATA device, connect the SATA power cable to this connector Panel voltage selection header (VCC_PWR_SEL) VCC_PWR_SEL 1 2 3 Pins 3V 5V 12V (Default) 1 (Default) 2 3 Setting 3V 5V 12V Panel off header (2-pin PANEL_OFF) This 2-pin header is for connecting a monitor switch that can turn off the LCD panel display backlight. Speaker connector (4-pin SPEAKER) This 4-pin connector is for the chassis-mounted system warning speaker. The speaker allows you to hear system beeps and warnings. Chapter 1: Product introduction 1-2 E11582_Q170T_UM.indb 2 2016-05-05 10:16:51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
1-2
Chapter 1: Product introduction
Internal DC power connector (2-pin ATX19V/12V)
This connector is for an ATX power supply. The plug
from the power supply is designed to fit this connector
in only one orientation. Find the proper orientation and
push down firmly until the connector completely fits.
PIN 1
ATX19V/12V
DC_JACK_IN
GND
CPU and chassis fan connectors (4-pin CPU_FAN, 4-pin CHA_FAN )
Connect the fan cables to the fan connectors on the motherboard, ensuring that the
black wire of each cable matches the ground pin of the connector.
Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside
the system may damage the motherboard components. These are not jumpers! Do not
place jumper caps on the fan connectors! The CPU_FAN connector supports a CPU fan
of maximum 1A (12 W) fan power.
Serial ATA 6.0Gb/s connectors (SATA6G_3~6)
These connectors connect to Serial ATA 6.0 Gb/s hard disk drives via Serial ATA
6.0 Gb/s signal cables.
USB 3.0 connector (20-1 pin USB3_12)
Connect a USB 3.0 module to this connector for additional USB 3.0 front or rear
panel ports. This connector complies with USB 3.0 specifications and provides
faster data transfer speeds of up to 5 Gbps, faster charging time for USB-
chargeable devices, optimized power efficiency, and backward compatibility with
USB 2.0.
DDR4 SO-DIMM slots
Install 2 GB, 4 GB, 8 GB, and 16 GB non-ECC un-buffered DDR4 SO-DIMMs into
these DIMM sockets.
SATA power connector (15-pin SATA_PWRCON)
This connector is for the SATA power cable. The power cable plug is designed to
fit this connector in only one orientation. Find the proper orientation and push down
firmly until the connector completely fit. To provide power to your SATA device,
connect the SATA power cable to this connector
Panel voltage selection header (VCC_PWR_SEL)
3
3V
(Default)
2
5V
1
12V
VCC_PWR_SEL
Panel off header (2-pin PANEL_OFF)
This 2-pin header is for connecting a monitor switch that can turn off the LCD panel
display backlight.
Speaker connector (4-pin SPEAKER)
This 4-pin connector is for the chassis-mounted system warning speaker. The
speaker allows you to hear system beeps and warnings.
Pins
Setting
1 (Default)
3V
2
5V
3
12V
E11582_Q170T_UM.indb
2
2016-05-05
10:16:51