Asus RS320Q-E7 RS12 User Guide

Asus RS320Q-E7 RS12 Manual

Get Asus RS320Q-E7 RS12 PDF manuals and user guides View all Asus RS320Q-E7 RS12 manuals
Add to My Manuals
Save this manual to your list of manuals

Asus RS320Q-E7 RS12 manual content summary:

  • Asus RS320Q-E7 RS12 | User Guide - Page 1
    RS320Q-E7/RS12 2U Rackmount Server User Guide
  • Asus RS320Q-E7 RS12 | User Guide - Page 2
    . ASUS assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual, including the products and software described in it. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification
  • Asus RS320Q-E7 RS12 | User Guide - Page 3
    Contents Notices...vii Safety information viii About this guide ix Chapter 1: Product introduction 1.1 System package contents 1-2 1.2 LEDs 1-10 1.7.3 HDD status LED 1-10 Chapter 2: Hardware setup 2.1 Chassis cover 2-2 2.2 Central Processing Unit (CPU 2-4 2.2.1 Installing the CPU 2-4 2.2.2
  • Asus RS320Q-E7 RS12 | User Guide - Page 4
    Contents 2.7.3 2.7.4 Installing ASMB5 series management board 2-19 Installing ASUS PIKE Riser Card (optional 2-20 Chapter 3: Installation options 3.1 Installing friction rail kit items 3-2 3.1.1 Attaching the fixing latches to the server 3-2 3.1.2 Mounting the server to the rack 3-5 Chapter
  • Asus RS320Q-E7 RS12 | User Guide - Page 5
    Contents 5.5.2 Trusted Computing 5-14 5.5.3 WHEA Support 5-14 5.5.4 CPU Configuration 5-15 5.5.5 North Bridge 5-17 5.5.6 South Bridge 5-17 5.5.7 SATA Configuration 5-18 5.5.8 Intel TXT(LT) Configuration 5-19 5.5.9 USB Configuration 5-19 5.5.10 ME Subsystem 5-20 5.5.
  • Asus RS320Q-E7 RS12 | User Guide - Page 6
    17 7.3 LAN driver installation 7-19 7.4 VGA driver installation 7-22 7.5 Management applications and utilities installation 7-25 7.5.1 Running the support DVD 7-25 7.5.2 Drivers menu 7-25 7.5.3 Utilities menu 7-26 7.5.4 Make disk menu 7-26 7.5.5 Contact information 7-26 Appendix: Reference
  • Asus RS320Q-E7 RS12 | User Guide - Page 7
    . This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer's instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation
  • Asus RS320Q-E7 RS12 | User Guide - Page 8
    to fix it by yourself. Contact a qualified service technician or your dealer. Operation Safety • Any operating the server, carefully read all the manuals included with the server package. • Before used batteries according to the manufacturer's instructions. CD-ROM Drive Safety Warning CLASS
  • Asus RS320Q-E7 RS12 | User Guide - Page 9
    the battery should not be placed in municipal waste. About this guide Audience This user guide is intended for system integrators, and experienced users with at least 7. Chapter 7: Driver installation This chapter provides instructions for installing the necessary drivers for different system
  • Asus RS320Q-E7 RS12 | User Guide - Page 10
    manual. DANGER/WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Instructions Web-based Management (ASWM) user guide This manual tells how to set up and
  • Asus RS320Q-E7 RS12 | User Guide - Page 11
    Product introduction Chapter 1 This chapter describes the general features of the chassis kit. It includes sections on front panel and rear panel specifications. 1-
  • Asus RS320Q-E7 RS12 | User Guide - Page 12
    Model Name Chassis Motherboard Component Accessories Optional Items RS320Q-E7/RS12 ASUS R21A 2U Rackmount Chassis ASUS P8BH 2 x Hot-swappable 3.5" HDD trays* 1 x RS320Q-E7 User's Guide 1 x RS320Q-E7 Support CD 1 x ASUS ASWM Enterprise User's Guide 1 x ASUS Web-based Management (ASWM) Enterprise
  • Asus RS320Q-E7 RS12 | User Guide - Page 13
    1.2 Serial number label For faster and quicker troubleshooting solutions from the ASUS Technical Support team, provide the product's serial number containing 12 characters such as xxS2xxxxxxxx as shown in the figure below. RS320Q-E7/RS12 xxS0xxxxxxxxxx ASUS RS320Q-E7/RS12 1-3
  • Asus RS320Q-E7 RS12 | User Guide - Page 14
    1.3 System specifications Model Name RS320Q-E7/RS12 Processor / System Bus Core Logic 1 x Socket LGA1155 per up to 32GB (UDIMM) Memory DDR3 1600*/1333/1066 ECC UDIMM Memory Type *DDR3 1600 is only supported by Intel® Xeon® E3-1200 v2 processor. Memory Size 1GB, 2GB, 4GB, 8GB (UDIMM) Total
  • Asus RS320Q-E7 RS12 | User Guide - Page 15
    Model Name Graphic VGA RS320Q-E7/RS12 Aspeed AST2050 + 16MB VRAM Per Node: Onboard I/O Connectors OS Support Out of Band Management Remote Solution Hardware Software Dimension (HH x WW x DD) Net Weight Kg (CPU, DRAM & HDD not included) Power Supply Power Rating Environment - 1 x
  • Asus RS320Q-E7 RS12 | User Guide - Page 16
    1.4 Front panel features Front panel Node 2 HDD 1 (Node 1) Node 1 HDD 1 (Node 2) HDD 1 (Node 3) Front panel HDD 1 (Node 4) Node 4 Node 3 HDD 2 (Node 1) HDD 2 (Node 2) HDD 2 (Node 3) HDD 2 (Node 4) HDD 3 (Node 1) HDD 3 (Node 2) HDD 3 (Node 3) HDD 3 (Node 4) Refer to section 1.7.1 Front
  • Asus RS320Q-E7 RS12 | User Guide - Page 17
    LAN port 2 LAN port 3* LAN port 1 VGA port Serial port USB ports * This port is for ASUS ASMB5-iKVM controller card only. 1.6 Internal features 6 4 6 5 3 1 2 ASUS RS320Q-E7/RS12 1-7
  • Asus RS320Q-E7 RS12 | User Guide - Page 18
    1. Power supply and power fan 2. ASUS P8BH Server Board 3. System fans 4. SATA/SAS backplane (hidden) 5. Hot-swap HDD trays (SAS and SATA) 6. Front LED Boards Turn off the system power and detach the power supply before removing or replacing any system component. The barebone server does not include
  • Asus RS320Q-E7 RS12 | User Guide - Page 19
    . Press the location button again to turn off. OFF No LAN connection Blinking LAN is transmitting or receiving data ON LAN connection is present ASUS RS320Q-E7/RS12 1-9
  • Asus RS320Q-E7 RS12 | User Guide - Page 20
    1.7.2 LAN (RJ-45) LEDs SPEED LED ACT/LINK LED ACT/LINK LED SPEED LED ACT/LINK LED Status Description OFF No link GREEN Linked BLINKING Data activity SPEED LED Status Description OFF 10 Mbps connection ORANGE 100 Mbps connection GREEN 1 Gbps connection 1.7.3 HDD status LED HDD
  • Asus RS320Q-E7 RS12 | User Guide - Page 21
    Hardware setup Chapter 2 This chapter lists the hardware setup procedures that you have to perform when installing or removing system components. 2-
  • Asus RS320Q-E7 RS12 | User Guide - Page 22
    2.1 Chassis cover Removing the top cover 1. Loosen the six screws on the top and the two sides of the top cover, as shown in the following figures. 2. Lift the rear end of the top cover (A), and slide the cover toward the rear panel (B) until it disengages from the chassis. B A 2-2 Chapter 2:
  • Asus RS320Q-E7 RS12 | User Guide - Page 23
    . When installing only two nodes, install the nodes to node slot number 1 and 3 or number 2 and 4. Refer to section 1.5 Rear panel features for details. ASUS RS320Q-E7/RS12 2-3
  • Asus RS320Q-E7 RS12 | User Guide - Page 24
    Merchandise Authorization (RMA) requests only if the motherboard comes with the cap on the LGA2011 socket. • The product warranty does not cover damage to the socket contacts resulting from incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the PnP cap. 2.2.1 Installing
  • Asus RS320Q-E7 RS12 | User Guide - Page 25
    lifted. Load lever A B Retention tab Load plate 4. Lift the tab only to remove the PnP cap from the CPU socket. PnP cap Cap tab ASUS RS320Q-E7/RS12 2-5
  • Asus RS320Q-E7 RS12 | User Guide - Page 26
    5. Position the CPU over the socket, ensuring that the gold triangle is on the bottom‑left corner of the socket, and then fit the socket alignment keys into the CPU notches. The CPU fits in only one correct orientation. DO NOT force the CPU into the socket to prevent bending the connectors on the
  • Asus RS320Q-E7 RS12 | User Guide - Page 27
    8. Insert the load lever under the retention tab. ASUS RS320Q-E7/RS12 2-7
  • Asus RS320Q-E7 RS12 | User Guide - Page 28
    2.2.2 Installing the CPU heatsink To install the CPU heatsink: 1. Place the heatsink on top of the installed CPU, ensuring that the four fasteners match the holes on the motherboard. 2. Twist each of the four screws with a Philips (cross) screwdriver just enough to attach the heatsink to the
  • Asus RS320Q-E7 RS12 | User Guide - Page 29
    install memory modules of the same version or data code (D/C) from the same vendor. Check with the retailer to get the correct memory modules. ASUS RS320Q-E7/RS12 2-9
  • Asus RS320Q-E7 RS12 | User Guide - Page 30
    DIMM notch damage. 2.3.4 Removing a DIMM 1. Simultaneously press the retaining clips outward to unlock the DIMM. 2 2. Remove the DIMM from the socket. 1 1 Support the DIMM lightly with your fingers when pressing the retaining clips. The DIMM might get damaged when it flips out with extra
  • Asus RS320Q-E7 RS12 | User Guide - Page 31
    2.4 Hard disk drives The system supports three hot-swap SATAII/SAS hard disk drives per node (available only when an optional ASUS PIKE SAS RAID card is secure the hard disk drive. 4. Place a SATAII/SAS hard disk drive on the tray, then secure it with four screws. ASUS RS320Q-E7/RS12 2-11
  • Asus RS320Q-E7 RS12 | User Guide - Page 32
    5. Carefully insert the drive tray and push it all the way to the depth of the bay until just a small fraction of the tray edge protrudes. When installed, the SATAII/SAS connector on the drive connects to the SATAII/SAS interface on the backplane. 6. Push the tray lever until it clicks, and secures
  • Asus RS320Q-E7 RS12 | User Guide - Page 33
    the screw from the slot bay. 4. Install a PCI Express x16 card to the bracket, and secure the card with a screw. PCI Express x16 slot ASUS RS320Q-E7/RS12 2-13
  • Asus RS320Q-E7 RS12 | User Guide - Page 34
    5. Press the riser card bracket until the golden connectors completely fit the slot and the bracket aligns with the rear panel. 6. Connect the cables to the card, if applicable. 2.5.2 Configuring an expansion card After installing the expansion card, configure it by adjusting the software settings.
  • Asus RS320Q-E7 RS12 | User Guide - Page 35
    ) 3. Panel connector (from motherboard to connection board) 4. SATA connectors (from motherboard to SATAII/SAS connection board) 5. Auxiliary panel connector (from motherboard to connection board) ASUS RS320Q-E7/RS12 2-15
  • Asus RS320Q-E7 RS12 | User Guide - Page 36
    2.7 Removable/optional components You may need to remove previously installed system components when installing or removing system devices. You may also need to install the optional components into the system. This section tells how to remove/install the following components: 1. System fans 2. Power
  • Asus RS320Q-E7 RS12 | User Guide - Page 37
    To install a second power supply module: 1. Press and hold the latch on the dummy cover and pull out the cover from the server chassis. 2. Firmly push the second power supply module into the chassis until lever. 2. Hold the power supply module lever and press the PSU latch. ASUS RS320Q-E7/RS12 2-17
  • Asus RS320Q-E7 RS12 | User Guide - Page 38
    3. Firmly pull the power supply module out of the system chassis. 4. Firmly push the new power supply module into the chassis until the latch locks to the server chassis. 2-18 Chapter 2: Hardware setup
  • Asus RS320Q-E7 RS12 | User Guide - Page 39
    2.7.3 Installing ASMB5 series management board To install the ASMB5 management board: 1. Locate the ASMB5 header on the motherboard. 2. Orient and press the ASMB5 management card in place. 3. Insert the LAN cable plug to the LAN3 port for server management. ASUS RS320Q-E7/RS12 2-19
  • Asus RS320Q-E7 RS12 | User Guide - Page 40
    2.7.4 Installing ASUS PIKE Riser Card (optional) To install ASUS PIKE riser card: 1. Remove the three screws on the riser card bracket. 2. Firmly hold the riser card bracket, and pull it up to detach it from the PCI Express x16 slot on the motherboard. 3. Locate the two screws on the riser card
  • Asus RS320Q-E7 RS12 | User Guide - Page 41
    chassis. 8. Connect the SGPIO cable to the SGPIO connector on the PIKE Riser card. 9. Remove the SATA/SAS cables from the onboard SATA1-3 connectors. ASUS RS320Q-E7/RS12 2-21
  • Asus RS320Q-E7 RS12 | User Guide - Page 42
    10. Connect the SATA/SAS cables to the SAS1-3 connectors on the PIKE riser card. 11. Align the riser card bracket to the PCI Express x16 slot on the motherboard. 12. Press the riser card bracket until the golden fingers completely fit the slot and the bracket aligns with the rear panel. 13. Move the
  • Asus RS320Q-E7 RS12 | User Guide - Page 43
    Installation options Chapter 3 This chapter describes how to install the optional components and devices into the barebone server. 2-
  • Asus RS320Q-E7 RS12 | User Guide - Page 44
    3.1 Installing friction rail kit items Your friction rail kit package contains: • One pair of rack rails • One pair of fixing latches • 4 latch screws, 4 rail screws and 4 rail washers Rail Washers Latch screws Rail screws Front end Fixing latches Rack rails Rear end 3.1.1 Attaching the
  • Asus RS320Q-E7 RS12 | User Guide - Page 45
    of the rail with two rack screws and washers. 8. Repeat steps 4 to 7 to attach the rack rail on the other side of the rack. ASUS RS320Q-E7/RS12 3-3
  • Asus RS320Q-E7 RS12 | User Guide - Page 46
    9. When mounting the server to the rack, ensure to include the side knots on the two sides of the server in the rack rail holders. DO NOT install the rail kit in the situations shown below: DO NOT place the rail hook on a thick lip of the mounting hole. DO NOT install the rail to the outer side of
  • Asus RS320Q-E7 RS12 | User Guide - Page 47
    to the rack. 2. Pull the server from the rack. Remember to press the latches on both sides to release the server from the rack. ASUS RS320Q-E7/RS12 3-5
  • Asus RS320Q-E7 RS12 | User Guide - Page 48
    3-6 Chapter 3: Installation options
  • Asus RS320Q-E7 RS12 | User Guide - Page 49
    Motherboard info Chapter 4 This chapter includes the motherboard layout, and brief descriptions of the jumpers and internal connectors. 34-1
  • Asus RS320Q-E7 RS12 | User Guide - Page 50
    4.1 P8BH Motherboard layouts 16 5 14 21 23 22 20 17 18 19 4 3 2 12 15 12 6 9 13 8 17 10 7 1 17 12 12 11 4-2 Chapter 4: Motherboard information
  • Asus RS320Q-E7 RS12 | User Guide - Page 51
    Management Controller LED (BMC_LED1) 22. P8BH +5 Power LED (+5V_LED) 23. Location LED (LOC_LED) Page 2-4 2-9 2-13 4-4 4-5 4-5 4-6 4-6 4-7 4-7 4-8 4-8 4-9 4-9 4-10 4-10 4-11 4-12 4-13 4-14 4-14 4-15 4-15 ASUS RS320Q-E7/RS12 4-3
  • Asus RS320Q-E7 RS12 | User Guide - Page 52
    4.2 Jumpers 1. Clear RTC RAM (CLRTC1) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system
  • Asus RS320Q-E7 RS12 | User Guide - Page 53
    ) These jumpers allow you to enable or disable the onboard Intel® Intel 82574LGigabit LAN controllers. Set to pins 1-2 to activate the Gigabit LAN feature. ASUS RS320Q-E7/RS12 4-5
  • Asus RS320Q-E7 RS12 | User Guide - Page 54
    4. RAID configuration utility selection (3-pin RAID_SEL1) This jumper allows you to select the RAID configuration utility to use when you create disk arrays. Place the jumper caps over pins 1-2 if you want to use the LSI Logic Embedded SATA RAID Setup Utility (default). Otherwise, place the jumper
  • Asus RS320Q-E7 RS12 | User Guide - Page 55
    SATA1, SATA2 [Blue]) (SATA 3Gb/s: 7-pin SATA3, SATA4, SATA5, SATA6 [Black]) Supported by the Intel® C204 chipset, these connectors are for the Serial ATA signal cables for Serial USB connectors comply with USB 2.0 specification that supports up to 480 Mbps connection speed. ASUS RS320Q-E7/RS12 4-7
  • Asus RS320Q-E7 RS12 | User Guide - Page 56
    place the other end to the device, which you want to monitor temperature. 4. Front fan connectors (FRNT_FAN1, FRNT_FAN2, FRNT_FAN3, FRNT_FAN4) The fan connectors support cooling fans of 350 mA-740 mA (8.88 W max.) or a total of 3.15 A-6.66 A (53.28 W max.) at +12V. Connect the fan cables to the fan
  • Asus RS320Q-E7 RS12 | User Guide - Page 57
    for the SGPIO peripherals for the Intel Rapid Storage Technology RAID SATA LED and LSI MegaRAID. 6. BMC header (BMC_FW1) The BMC connector on the motherboard supports an ASUS® Server Management Board 5 Series (ASMB5). ASUS RS320Q-E7/RS12 4-9
  • Asus RS320Q-E7 RS12 | User Guide - Page 58
    using the SMBus interface. This connector functions only when you install the ASUS ASMB5. 8. TPM connector (20-1 pin TPM) This connector supports a Trusted Platform Module (TPM) system, which can securely store keys, digital certificates, passwords, and data. A TPM system also helps enhance network
  • Asus RS320Q-E7 RS12 | User Guide - Page 59
    POWER SUPPLY ONLY; otherwise you may damage the motherboard. Ensure that your PSU can provide at least the minimum power required by your system. ASUS RS320Q-E7/RS12 4-11
  • Asus RS320Q-E7 RS12 | User Guide - Page 60
    10. System panel connector (20-pin PANEL1) This connector supports several chassis-mounted functions. 1. System power LED (3-pin PLED) This 3-pin connector is for the system power LED. Connect the chassis power LED cable to
  • Asus RS320Q-E7 RS12 | User Guide - Page 61
    Button/Switch (2-pin LOCATORBTN) These leads are for the locator button on the front panel. This button queries the state of the system locator. ASUS RS320Q-E7/RS12 4-13
  • Asus RS320Q-E7 RS12 | User Guide - Page 62
    4.4 Internal LEDs 1. Standby Power LED (SB_PWR1) The motherboard comes with a standby power LED. The green LED lights up to indicate that the system is ON, in sleep mode, or in soft-off mode. This is a reminder that you should shut down the system and unplug the power cable before removing or
  • Asus RS320Q-E7 RS12 | User Guide - Page 63
    3. P8BH +5V Power LED (+5V_LED) This LED lights up when you turn on the system using the Power-on button. 4. Location LED (LOC_LED) This LED lights up for you to conveniently locate the system in error. ASUS RS320Q-E7/RS12 4-15
  • Asus RS320Q-E7 RS12 | User Guide - Page 64
    4-16 Chapter 4: Motherboard information
  • Asus RS320Q-E7 RS12 | User Guide - Page 65
    BIOS setup Chapter 5 This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided. 3-
  • Asus RS320Q-E7 RS12 | User Guide - Page 66
    5.1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup: 1. ASUS CrashFree BIOS 3 (To recover the BIOS using a bootable USB flash disk drive when the BIOS file fails or gets corrupted.) 2. ASUS EZ Flash 2 (
  • Asus RS320Q-E7 RS12 | User Guide - Page 67
    to find the BIOS file, and then press to perform the BIOS update process. Reboot the system when the update process is done. ASUS RS320Q-E7/RS12 5-3
  • Asus RS320Q-E7 RS12 | User Guide - Page 68
    file for the motherboard. Save the BIOS file to a bootable USB flash disk drive. 2. Copy the BUPDATER utility (BUPDATER.exe) from the ASUS support website at support.asus.com to the bootable USB flash disk drive you created earlier. 3. Boot the system in DOS mode, then at the prompt, type: BUPDATER
  • Asus RS320Q-E7 RS12 | User Guide - Page 69
    after the BIOS update process is completed. Reboot the system from the hard disk drive. The BIOS update is finished! Please restart your system. C:\> ASUS RS320Q-E7/RS12 5-5
  • Asus RS320Q-E7 RS12 | User Guide - Page 70
    5.2 BIOS setup program This motherboard supports a programmable firmware chip that you can update using the provided utility described in section 5.1 Managing and updating your BIOS. Use the BIOS Setup program when
  • Asus RS320Q-E7 RS12 | User Guide - Page 71
    To select an item on the menu bar, press the right or left arrow key on the keyboard until the desired item is highlighted. ASUS RS320Q-E7/RS12 5-7
  • Asus RS320Q-E7 RS12 | User Guide - Page 72
    5.2.3 Menu items The highlighted item on the menu bar displays the specific items for that menu. For example, selecting Main shows the Main menu items. The other items (Event Logs, Advanced, Monitor, Boot, Tool, and Exit) on the menu bar have their respective menu items. 5.2.4 Submenu items A solid
  • Asus RS320Q-E7 RS12 | User Guide - Page 73
    . • The Administrator or User Password items on top of the screen show the default Not Installed. After you set a password, these items show Installed. ASUS RS320Q-E7/RS12 5-9
  • Asus RS320Q-E7 RS12 | User Guide - Page 74
    Administrator Password If you have set an administrator password, we recommend that you enter the administrator password for accessing the system. Otherwise, you might be able to see or change only selected fields in the BIOS setup program. To set an administrator password: 1. Select the
  • Asus RS320Q-E7 RS12 | User Guide - Page 75
    boot event. Configuration options: [Enabled] [Disabled] MECI [xx] Allows you to adjust value for the MECI (Multiple Event Count Increment) using the and keys. ASUS RS320Q-E7/RS12 5-11
  • Asus RS320Q-E7 RS12 | User Guide - Page 76
    METW [xx] Allows you to adjust value for the METW (Multiple Event Time Window) using the and keys. Log OEM Codes [Enabled] Allows you to enable or disable the logging of EFI status codes as OEM codes. Configuration option: [Disabled] [Enabled] Convert OEM Codes [Disabled] Allows you to
  • Asus RS320Q-E7 RS12 | User Guide - Page 77
    [S3 (Suspend to RAM)] Allows you to set the ACPI Sleep State. Configuration options: [Suspend Disabled] [S1 (CPU Stop Clock)] [S3 (Suspend to RAM)] ASUS RS320Q-E7/RS12 5-13
  • Asus RS320Q-E7 RS12 | User Guide - Page 78
    - Copyright (C) 2012 American Megatrends, Inc. Advanced TPM Configuration TPM SUPPORT [Enabled] Current TPM Status Information NO TPM Hardware Enables or Disables TPM support. O.S. will not show TPM. Reset of platform is required. TPM SUPPORT [Enabled] Allows you to enable or disable the TPM
  • Asus RS320Q-E7 RS12 | User Guide - Page 79
    that the BIOS automatically detects. Some items may not appear if your CPU does not support the related functions. Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc. Advanced CPU to always return to zero (0). Configuration options: [Disabled] [Enabled] ASUS RS320Q-E7/RS12 5-15
  • Asus RS320Q-E7 RS12 | User Guide - Page 80
    you to enable or disable the Intel® Turbo Mode Technology. Configuration options: [Disabled] [Enabled] CPU C1E [Enabled] [Enabled] Enables the C1E support function. This item should be enabled in order to enable the Enhanced Halt State. [Disabled] Disables this function. CPU C3 Report [Enabled
  • Asus RS320Q-E7 RS12 | User Guide - Page 81
    the High Precision Event Timer. High Precision Timer [Enabled] Allows you to enable or disable the High Precision Event Timer. Configuration options: [Enabled] [Disabled] ASUS RS320Q-E7/RS12 5-17
  • Asus RS320Q-E7 RS12 | User Guide - Page 82
    5.5.7 SATA Configuration While entering Setup, the BIOS automatically detects the presence of SATA devices. The SATA Port items show Not Present if no SATA device is installed to the corresponding SATA port. Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc. Advanced SATA
  • Asus RS320Q-E7 RS12 | User Guide - Page 83
    controller legacy mode is enabled. If no USB device is detected, the legacy USB support is disabled. Configuration options: [Disabled] [Enabled] [Auto] EHCI Hand-off [Disabled] Enables or disables the BIOS EHCI hand-off support. Configuration options: [Disabled] [Enabled] ASUS RS320Q-E7/RS12 5-19
  • Asus RS320Q-E7 RS12 | User Guide - Page 84
    -out value. Configuration options: [10 sec] [20 sec] [30 sec] [40 sec] Device power-up delay [Auto] Configuration options: [Auto] [Manual] 5.5.10 ME Subsystem Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc. Advanced Intel ME Subsystem Configuration ME Subsystem [Enabled] ME
  • Asus RS320Q-E7 RS12 | User Guide - Page 85
    =4] [IO=3F8h: IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12] [IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12] [IO=3E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12] [IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12] ASUS RS320Q-E7/RS12 5-21
  • Asus RS320Q-E7 RS12 | User Guide - Page 86
    5.5.12 APM Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc. Advanced EuP Ready Restrore AC Power Loss Power On By PCIE Power On By Ring Power On By RTC [Disabled] [Power Off] [Disabled] [Disabled] [Disabled] Specify what state to go to when power is re-applied after a power
  • Asus RS320Q-E7 RS12 | User Guide - Page 87
    Out-of-Band Management/ Windows Emergency Management Services (EMS) Console Redirection Console Redirection Settings VT100 to support color, function keys, etc. [VT-UTF8] Uses UTF8 encoding to map Unicode chars onto 1 or more bytes [ANSI] Extended ASCII char set ASUS RS320Q-E7/RS12 5-23
  • Asus RS320Q-E7 RS12 | User Guide - Page 88
    to send start/stop signals. Configuration options: [None] [Hardware RTS/CTS] VT-UTF8 Combo Key Support [Enabled] Allows you to enable and disable the VT-UTF8 combination key support for ANSI/ VT100 terminals. Configuration options: [Enabled] [Disabled] Recorder Mode [Disabled] With this mode
  • Asus RS320Q-E7 RS12 | User Guide - Page 89
    onboard hardware monitor automatically detects the voltage output through the onboard voltage regulators. Select Ignore if you do not want to detect this item. ASUS RS320Q-E7/RS12 5-25
  • Asus RS320Q-E7 RS12 | User Guide - Page 90
    Exit Setup Prompt Timeout Bootup NumLock State Full Screen Logo Option ROM Messages INT19 Trap Response Boot Device Seeking Load RT32 Image CSM Support UEFI Boot 5 [On] [Enabled] [Force BIOS] [Enabled] [Endless PXE] [Enalbed] [Enabled] [Disabled] Number of seconds to wait for setup activation key
  • Asus RS320Q-E7 RS12 | User Guide - Page 91
    [Disabled] Enables or disables the CSM Support. Configuration options: [Disabled] [Enabled] [Auto] UEFI Boot [Disabled] Enables or disables the UEFI Boot. Coniguration options: [Disabled installed in the system. Click an item to start booting from the selected device. ASUS RS320Q-E7/RS12 5-27
  • Asus RS320Q-E7 RS12 | User Guide - Page 92
    5.8 Tool menu The Tool menu items allow you to configure options for special functions. Select an item then press to display the submenu. Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc. Main Event Logs Advanced Monitor Boot Tool Exit ASUS EZ Flash Utility Be used to
  • Asus RS320Q-E7 RS12 | User Guide - Page 93
    from filesystem device This option allows you to attempt to launch the EFI Shell application (shellx64.efi) from one of the available filesystem devices. ASUS RS320Q-E7/RS12 5-29
  • Asus RS320Q-E7 RS12 | User Guide - Page 94
    5-30 Chapter 5: BIOS setup
  • Asus RS320Q-E7 RS12 | User Guide - Page 95
    RAID configuration Chapter 6 This chapter provides instructions for setting up, creating and configuring RAID sets using the available utilities. 3-
  • Asus RS320Q-E7 RS12 | User Guide - Page 96
    Storage Technology with RAID 0, RAID 1, RAID 10, and RAID 5 support (for Windows OS only). 6.1.1 RAID definitions RAID 0 (Data striping drive included in a created RAID set, copy first the RAID driver from the support DVD to a floppy disk before you install an operating system to the selected hard
  • Asus RS320Q-E7 RS12 | User Guide - Page 97
    the SATA hard disks into the drive bays following the instructions in the system user guide. 2. Connect a SATA signal cable to the signal connector supported by the Intel® C602 chipset. Refer to the succeeding section for details on how to use the RAID configuration utility. ASUS RS320Q-E7/RS12
  • Asus RS320Q-E7 RS12 | User Guide - Page 98
    (s) from SATA hard disk drives connected to the SATA connectors supported by the motherboard southbridge chip. To enter the LSI MegaRAID software utility, the boot priority of the SATA optical drive has to be manually adjusted. Otherwise, the system will not boot from the connected SATA ODD
  • Asus RS320Q-E7 RS12 | User Guide - Page 99
    New. In Easy Configuration, the virtual drive parameters are set automatically. In New Configuration, you manually set the virtual drive parameters. Using Easy Configuration To create a RAID set using the Easy to Navigate Between Items And Press Enter To Select An Option ASUS RS320Q-E7/RS12 6-5
  • Asus RS320Q-E7 RS12 | User Guide - Page 100
    2. The ARRAY SELECTION MENU displays the available drives connected to the SATA ports. Use the up/down arrow keys to select the drives you want to include in the RAID set, and then press . When selected, the drive indicator changes from READY to ONLIN A[X]-[Y], where X is the array number,
  • Asus RS320Q-E7 RS12 | User Guide - Page 101
    Accept SPAN = NO ONLINE Choose RAID Level For This VD Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option ASUS RS320Q-E7/RS12 6-7
  • Asus RS320Q-E7 RS12 | User Guide - Page 102
    8. Select Units from the Virtual Drive sub-menu, and then press . 9. Select the units for virtual drive size from the menu, and then press . LSI Software RAID Configuration Utility Ver C.05 Feb 17, 2012 BIOVSirVteuraslioDnriveA(.s1)0.C0o9n2fi3g1u5r2e3dR LD RAID E a sSyizeC o n f#
  • Asus RS320Q-E7 RS12 | User Guide - Page 103
    Consi0stency 1 148.580GB 2 64 KB ONLINE Select Yes Or No Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option ASUS RS320Q-E7/RS12 6-9
  • Asus RS320Q-E7 RS12 | User Guide - Page 104
    Using New Configuration When a RAID set already exists, using the New Configuration command erases the existing RAID configuration data. If you do not want to delete the existing RAID set, use the View/Add Configuration command to view or create another RAID configuration. To create a RAID set
  • Asus RS320Q-E7 RS12 | User Guide - Page 105
    displays at the bottom of the screen. 3. Follow step 3 to 12 of section 6.2.1 Creating a RAID set: Using Easy Configuration to add a new RAID set. ASUS RS320Q-E7/RS12 6-11
  • Asus RS320Q-E7 RS12 | User Guide - Page 106
    6.2.3 Initializing the virtual drives After creating the RAID set(s), you must initialize the virtual drives. You may initialize the virtual drives of a RAID set(s) using the Initialize or Objects command on the Management Menu. Using the Initialize command To initialize the virtual drive using the
  • Asus RS320Q-E7 RS12 | User Guide - Page 107
    Proce4ss 64 KB Objects Rebuild VD 0 Initialization Complete. Press Esc.. Check Consistency ¦ 100% Completed Virtual Virtual Drive 0 Status ONLINE SPACE-(De)Select, F10-Initialize ASUS RS320Q-E7/RS12 6-13
  • Asus RS320Q-E7 RS12 | User Guide - Page 108
    Using the Objects command To initialize the virtual drives using the Objects command 1. From the Management Menu, select Objects > Virtual Drive, and then press . LSI Software RAID Configuration Utility Ver C.05 Feb 17, 2012 BIOS Version A.10.09231523R Objects Management MAednaupter Configure
  • Asus RS320Q-E7 RS12 | User Guide - Page 109
    Press Enter To Select An Option 5. A progress bar appears on screen. If desired, press to abort initialization. When initialization is completed, press . ASUS RS320Q-E7/RS12 6-15
  • Asus RS320Q-E7 RS12 | User Guide - Page 110
    6.2.4 Rebuilding failed drives You can manually rebuild failed hard disk drives using the Rebuild command in the Management Menu. To rebuild a failed hard disk drive 1. From the Management Menu, select Rebuild,
  • Asus RS320Q-E7 RS12 | User Guide - Page 111
    HDS728080PLA380 PF20A60A SPACE-(De)Select,F10-Start Rebuild,F2-Drive Information,F3-View Virtual Drives 4. When rebuild is complete, press any key to continue. ASUS RS320Q-E7/RS12 6-17
  • Asus RS320Q-E7 RS12 | User Guide - Page 112
    6.2.5 Checking the drives for data consistency You can check and verify the accuracy of data redundancy in the selected virtual drive. The utility can automatically detect and/or detect and correct any differences in data redundancy depending on the selected option in the Objects > Adapter menu. The
  • Asus RS320Q-E7 RS12 | User Guide - Page 113
    check. • Abort - Aborts the consistency check. When you restart checking, it continues from zero percent. 5. When checking is complete, press any key to continue. ASUS RS320Q-E7/RS12 6-19
  • Asus RS320Q-E7 RS12 | User Guide - Page 114
    Using the Objects command To check data consistency using the Objects command 1. From the Management Menu, select Objects, and then select Virtual Drive from the sub-menu. 2. Use the arrow keys to select the virtual drive you want to check, and then press . 3. Select Check Consistency from
  • Asus RS320Q-E7 RS12 | User Guide - Page 115
    Keys To Navigate Between Items And Press Enter To Select An Option The utility clears all the current array(s). 3. Press any key to continue. ASUS RS320Q-E7/RS12 6-21
  • Asus RS320Q-E7 RS12 | User Guide - Page 116
    6.2.7 Selecting the boot drive from a RAID set You must have created a new RAID configuration before you can select the boot drive from a RAID set. See section 5.2.1 Creating a RAID set: Using New Configuration for details. To select the boot drive from a RAID set 1. From the Management Menu,
  • Asus RS320Q-E7 RS12 | User Guide - Page 117
    6.2.8 Enabling WriteCache You may manually enable the RAID controller's WriteCache option after creating a RAID set to improve the data transmission performance. adapter and press . Select View/Update Parameters and press to display the adapter properties. ASUS RS320Q-E7/RS12 6-23
  • Asus RS320Q-E7 RS12 | User Guide - Page 118
    4. Select Disk WC, and then press to turn on the option. LSI Software RAID Configuration Utility Ver C.05 Feb 17, 2012 BIOS Version A.10.09231523R Virtual Drive RAID = 0 CIORConbehnijbeMfteucaigiciknuatlarlsdCgeioeznmeseinstteAVPndihcaryyptstuieacrlalODbrDjireSS#
  • Asus RS320Q-E7 RS12 | User Guide - Page 119
    1+0), and RAID 5 set(s) from Serial ATA hard disk drives that are connected to the Serial ATA connectors supported by the Southbridge. To enter the Intel® Rapid Storage Technology option ROM utility: 1. Install all the Serial not exactly match the items on your screen. ASUS RS320Q-E7/RS12 6-25
  • Asus RS320Q-E7 RS12 | User Guide - Page 120
    6.3.1 Creating a RAID set To create a RAID set 1. From the utility main menu, select 1. Create RAID Volume and press . The following screen appears. Intel(R) Rapid Storage Technology - Option ROM - 10.1.0.1008 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. [ CREATE VOLUME MENU
  • Asus RS320Q-E7 RS12 | User Guide - Page 121
    [ HELP ] Enter a unique volume name that has no special characters and is 16 characters or less. [↑↓]Change [TAB]-Next [ESC]-Previous Menu [ENTER]-Select ASUS RS320Q-E7/RS12 6-27
  • Asus RS320Q-E7 RS12 | User Guide - Page 122
    2. Enter a name for the recovery set and press . 3. When the RAID Level item is selected, press the up/down arrow keys to select Recovery, and then press . 4. When the Disks item is selected, press to select the hard disk drives you want to include in the recovery set. The
  • Asus RS320Q-E7 RS12 | User Guide - Page 123
    volume "Volume0"? (Y/N): 3. Press to delete the RAID set and return to the utility main menu, or press to return to the DELETE VOLUME menu. ASUS RS320Q-E7/RS12 6-29
  • Asus RS320Q-E7 RS12 | User Guide - Page 124
    6.3.4 Resetting disks to Non-RAID Take caution before you reset a RAID volume hard disk drive to non-RAID. Resetting a RAID volume hard disk drive deletes all internal RAID structure on the drive. To reset a RAID set hard disk drive: 1. From the utility main menu, select 3. Reset Disks to Non-RAID
  • Asus RS320Q-E7 RS12 | User Guide - Page 125
    then press to select. A small triangle marks the selected drive. Press after completing your selection and return to the utility main menu. ASUS RS320Q-E7/RS12 6-31
  • Asus RS320Q-E7 RS12 | User Guide - Page 126
    6.3.6 Exiting the Intel® Rapid Storage Technology utility To exit the utility: 1. From the utility main menu, select 4. Exit, and then press . The following warning message appears. [ CONFIRM EXIT ] Are you sure you want to exit? (Y/N): 2. Press to exit or press to return to the
  • Asus RS320Q-E7 RS12 | User Guide - Page 127
    size as the original hard disk. 2. Reboot the system and then follow the steps in section Rebuilding the RAID with other non-RAID disk. ASUS RS320Q-E7/RS12 6-33
  • Asus RS320Q-E7 RS12 | User Guide - Page 128
    6.3.8 Setting the Boot array in the BIOS Setup Utility You can set the boot priority sequence in the BIOS for your RAID arrays when creating multiRAID using the Intel® Rapid Storage Technology. To set the boot array in the BIOS: Set at least one of the arrays bootable to boot from the hard disk. 1.
  • Asus RS320Q-E7 RS12 | User Guide - Page 129
    Driver installation Chapter 7 This chapter provides instructions for installing the necessary drivers for different system components.
  • Asus RS320Q-E7 RS12 | User Guide - Page 130
    or bootable array. This part provides the instructions on how to install the RAID controller drivers of the SATA optical disk drive has to be manually adjusted. Otherwise, the system will not boot from as the first boot priority to boot from the support DVD. Save your changes, and then exit the BIOS
  • Asus RS320Q-E7 RS12 | User Guide - Page 131
    bit SLES 11 32 bit 6. Locate the RAID driver and place a blank, high-density floppy disk to the floppy disk drive. 7. Press . 8. Follow screen instructions to create the driver disk. ASUS RS320Q-E7/RS12 7-3
  • Asus RS320Q-E7 RS12 | User Guide - Page 132
    Start Windows®. 2. Place the motherboard support DVD into the optical drive. 3. Go to the Make disk menu, and then select the type of RAID driver disk you want to create. 4. Insert a floppy disk into the USB floppy disk drive. 5. Follow succeeding screen instructions to complete the process. Write
  • Asus RS320Q-E7 RS12 | User Guide - Page 133
    chosen to manually specify an adapter. Currently, Setup will load support for the support disks from a mass storage device manufacturer, or do not want to specify additional mass storage devices for use with Windows, press ENTER. S=Specify Additional Device ENTER=Continue F3=Exit ASUS RS320Q-E7/RS12
  • Asus RS320Q-E7 RS12 | User Guide - Page 134
    . Windows Setup Please insert the disk labelled Manufacturer-supplied hardware support disk into Drive A: * Press ENTER when ready. ENTER=Continue . 7. Setup then proceeds with the OS installation. Follow screen instructions to continue. To an existing Windows® Server OS To install the
  • Asus RS320Q-E7 RS12 | User Guide - Page 135
    from the menu. 5. Click the Driver tab, and then click the Driver Details button to display the RAID controller drivers. 6. Click OK when finished. ASUS RS320Q-E7/RS12 7-7
  • Asus RS320Q-E7 RS12 | User Guide - Page 136
    Red Hat® Enterprise Linux OS 4.7/4.8 To install the RAID controller driver when installing Red Hat® Enterprise OS: 1. Boot the system from the Red Hat® OS installation CD. 2. At the boot:, type linux dd. 3. Press . - To install or upgrade in graphical mode, press the key. - To install
  • Asus RS320Q-E7 RS12 | User Guide - Page 137
    begin testing the CD media before installation press OK. Choose Skip to skip the media test and start the installation. OK Skip 8. Follow the onscreen instructions to finish installing the RedHat operating system. ASUS RS320Q-E7/RS12 7-9
  • Asus RS320Q-E7 RS12 | User Guide - Page 138
    Red Hat® Enterprise Linux OS 5.0 To install the RAID controller driver when installing Red Hat® Enterprise OS: 1. Boot the system from the Red Hat® OS installation CD. 2. At the boot:, type linux dd. 3. Press . - To install or upgrade in graphical mode, press the key. - To install or
  • Asus RS320Q-E7 RS12 | User Guide - Page 139
    RAID controller drivers, select No, then press . More Driver Disks? Do you wish to load any more driver disks? Yes No 7. Follow the onscreen instructions to finish the OS installation. ASUS RS320Q-E7/RS12 7-11
  • Asus RS320Q-E7 RS12 | User Guide - Page 140
    SUSE Linux 11 OS To install the RAID controller driver when installing SUSE Linux Enterprise Server OS: 1. Boot the system from the SUSE OS installation CD. 2. Use the arrow keys to select Installation from the Boot Options menu. Boot from Hard Disk Installation Repair Installed System Rescue
  • Asus RS320Q-E7 RS12 | User Guide - Page 141
    (sda) as the driver update medium. Select OK, then press . Please choose the Driver Update medium. sda: USB Floppy Other device OK Back ASUS RS320Q-E7/RS12 7-13
  • Asus RS320Q-E7 RS12 | User Guide - Page 142
    Installing SUSE 11 Linux OS To install the LSI MegaRAID controller driver when installing SUSE Linux Enterprise Server OS: 1. Boot the system from the SUSE OS installation CD. 2. Use the arrow keys to select Installation from the Boot Options menu. 3. Press , then select Yes from the menu. Press
  • Asus RS320Q-E7 RS12 | User Guide - Page 143
    medium. Select OK, then press . Please choose the Driver Update medium. sda: USB Floppy other device OK Back 6. Select Back and follow the onscreen instructions to finish the installation. ASUS RS320Q-E7/RS12 7-15
  • Asus RS320Q-E7 RS12 | User Guide - Page 144
    -ROM, ASUS DRW-1612BLT sdb: Disk, Promise 1X2 Morror/RAID1 sd3: Disk, Promise RAID Console other device OK Back 7. Select Back and follow the onscreen instructions to finish the installation. 7-16 Chapter 7: Driver installation
  • Asus RS320Q-E7 RS12 | User Guide - Page 145
    the support DVD to locate the file ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to run the support DVD. 3. Click the item Intel Chipset Device Software from the menu. 4. The Intel(R) Chipset Device Software window appears. Click Next to start installation. ASUS RS320Q-E7/RS12 7-17
  • Asus RS320Q-E7 RS12 | User Guide - Page 146
    5. Select Yes to accept the terms of the License Agreement and continue the process. 6. Read the Readme File Information and press Next to continue the installation. 7. After completing the installation, click Finish to complete the setup process. 7-18 Chapter 7: Driver installation
  • Asus RS320Q-E7 RS12 | User Guide - Page 147
    the support DVD to locate the file ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to run the DVD. 3. Click the Intel® PRO/1000 Gigabit Adapters Driver to begin installation. 4. Click Next when the Intel(R) Network Connections-InstallShield Wizard window appears. ASUS RS320Q-E7/RS12
  • Asus RS320Q-E7 RS12 | User Guide - Page 148
    5. Tick I accept the terms in the license agreement and click Next to continue. 6. Click the Intel(R) PROSet for Windows Device Manager box, and then click Next to start the installation. 7-20 Chapter 7: Driver installation
  • Asus RS320Q-E7 RS12 | User Guide - Page 149
    7. Follow the screen instructions to complete installation. 8. When finished, press Finish to continue. ASUS RS320Q-E7/RS12 7-21
  • Asus RS320Q-E7 RS12 | User Guide - Page 150
    This section provides the instructions on how to install the ASPEED Video Graphics Adapter (VGA) driver. You need to manually install the ASPEED Administrator privileges. 2. Insert the motherboard/system support DVD to the optical drive. The support DVD automatically displays the Drivers menu if
  • Asus RS320Q-E7 RS12 | User Guide - Page 151
    5. Tick I accept the terms in the license agreement and click Next to continue. 6. Enter the user information and click Next to continue. 7. Select a setup type and click Next to continue. ASUS RS320Q-E7/RS12 7-23
  • Asus RS320Q-E7 RS12 | User Guide - Page 152
    8. Click Install to start driver installation. 9. When the installation completes, click Finish to restart your computer before using the program. 7-24 Chapter 7: Driver installation
  • Asus RS320Q-E7 RS12 | User Guide - Page 153
    run the support DVD. 7.5.2 Drivers menu The Drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices. The screen display and driver options vary under different operating system versions. ASUS RS320Q-E7/RS12 7-25
  • Asus RS320Q-E7 RS12 | User Guide - Page 154
    menu The Utilities menu displays the software applications and utilities that the motherboard supports. Click an item to install. 7.5.4 Make disk menu The Make disk menu . You can also find this information on the inside front cover of this user guide. 7-26 Chapter 7: Driver installation
  • Asus RS320Q-E7 RS12 | User Guide - Page 155
    Appendix This appendix includes additional information that you may refer to when configuring the motherboard. Reference info
  • Asus RS320Q-E7 RS12 | User Guide - Page 156
    A.1 P8BH block diagram A-2 Appendix A: Reference information
  • Asus RS320Q-E7 RS12 | User Guide - Page 157
    +886-2-2894-3447 Fax +886-2-2894-7798 E-mail [email protected] Web site http://www.asus.com Technical Support Telephone Online support +886-21-58660909 http://support.asus.com/techserv/techserv.aspx ASUSTeK COMPUTER INC. (Taiwan) Address 15 Li-Te Road, Peitou, Taipei, Taiwan 11259
  • Asus RS320Q-E7 RS12 | User Guide - Page 158
    Way, Fremont, CA 94539, USA Fax +1-510-608-4555 Web site http://usa.asus.com Technical Support Support fax General Support Online support +1-812-284-0883 +1-812-282-2787 http://support.asus.com/techserv/techserv.aspx ASUS COMPUTER GmbH (Germany and Austria) Address Harkort Str. 21-23
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
2U Rackmount Server
RS320Q-E7/RS12
User Guide