Asus RS724QA-E6 RS12 User Guide - Page 42

Creating IS Volumes

Get Asus RS724QA-E6 RS12 PDF manuals and user guides View all Asus RS724QA-E6 RS12 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

5.2 Creating IS Volumes The SAS BIOS CU is part of the Fusion-MPT BIOS. When the BIOS loads during boot and you see the message about the LSI Configuration Utility, press Ctrl-C to start it. After you do this, the message changes to: Please wait, invoking SAS Configuration Utility... After a brief pause, the main menu of the SAS BIOS CU appears. On some systems, however, the following message appears next: LSI Logic Configuration Utility will load following initialization! In this case, the SAS BIOS CU will load after the system has completed its power-on self test. Follow the steps below to configure an Integrated Striping (IS) volume with the SAS BIOS CU. The procedure assumes that the required controller(s) and disks are already installed in the computer system. You can configure an IM/IME volume and an IS volume on the same SAS controller. 1. On the Adapter List screen of the SAS BIOS CU, use the arrow keys to select a SAS adapter. 2. Press Enter to go to the Adapter Properties screen, shown in Figure 5.1. 5-2 Creating Integrated Striping Volumes Version 1.1 Copyright © 2006, 2007 by LSI Logic Corporation. All rights reserved.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
5-2
Creating Integrated Striping Volumes
Version 1.1
Copyright © 2006, 2007 by LSI Logic Corporation. All rights reserved.
5.2
Creating IS Volumes
The SAS BIOS CU is part of the Fusion-MPT BIOS. When the BIOS
loads during boot and you see the message about the LSI Configuration
Utility, press Ctrl-C to start it. After you do this, the message changes to:
Please wait, invoking SAS Configuration Utility...
After a brief pause, the main menu of the SAS BIOS CU appears. On
some systems, however, the following message appears next:
LSI Logic Configuration Utility will load following
initialization!
In this case, the SAS BIOS CU will load after the system has completed
its power-on self test.
Follow the steps below to configure an Integrated Striping (IS) volume
with the SAS BIOS CU. The procedure assumes that the required
controller(s) and disks are already installed in the computer system. You
can configure an IM/IME volume and an IS volume on the same SAS
controller.
1.
On the Adapter List screen of the SAS BIOS CU, use the arrow keys
to select a SAS adapter.
2.
Press Enter to go to the Adapter Properties screen, shown in
Figure 5.1
.