Home » Asus Manuals » Servers » Asus RS724QA-E6 RS12 » Manual Viewer

Asus RS724QA-E6 RS12 User Guide - Page 43

Adapter Properties Screen, Properties, Create IS, Volume, by pressing the + key

View all Asus RS724QA-E6 RS12 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Figure 5.1 Adapter Properties Screen LSI Logic MPT Setup Utility vx.xx.xx.xx Adapter Properties -- SAS1068 Adapter PCI Slot PCI Address(Bus/Dev/Func) MPT Firmware Revision SAS Address Status Boot Order Boot Support SAS1068 03 03:00:00 00.03.23.00-IT 500605B0:0000C580 Enabled 1 [Enabled BIOS & OS] RAID Properties SAS Topology Advanced Adapter Properties Esc = Exit Menu F1/Shift+1 = Help Enter = Select Item -/+ = Change Item 3. On the Adapter Properties screen, use the arrow keys to select RAID Properties and press Enter. 4. When you are prompted to select a volume type, select Create IS Volume. The Create New Array screen shows a list of disks that can be added to a volume. 5. Move the cursor to the RAID Disk column. To add a disk to the volume, change the No to Yes by pressing the + key, − key, or space bar. As disks are added, the Array Size ﬁeld changes to reﬂect the size of the new volume. There are several limitations when creating an IS (RAID 0) volume: - All disks must be either SATA (with extended command set support) or SAS (with SMART support). - Disks must have 512-byte blocks and must not have removable media. - There must be at least two and no more than ten drives in a valid IS volume. Hot spare drives are not allowed. Creating IS Volumes 5-3 Version 1.1 Copyright © 2006, 2007 by LSI Logic Corporation. All rights reserved.

Section	Page
Integrated RAID for SAS	1
Chapter1 Introduction to Integrated RAID	13
1.1 Introduction	13
1.2 Integrated RAID Benefits and Features	14
1.3 Using this Manual	15
Chapter2 Overview of Integrated Mirroring and Integrated Mirroring Enhanced	17
2.1 Introduction	17
2.2 IM and IME Features	18
2.3 IM/IME Description	19
2.4 Integrated RAID Firmware	21
2.4.1 Resynchronization with Concurrent Host I/O Operation	21
2.4.2 Metadata Support	21
2.4.3 Hot Swapping	22
2.4.4 SMART Support	22
2.4.5 Hot Spare Disk	22
2.4.6 Media Verification	23
2.4.7 Disk Write Caching	23
2.4.8 NVSRAM Usage	23
2.5 Fusion-MPT Support	23
Chapter3 Creating IM and IME Volumes	25
3.1 IM/IME Configuration Overview	25
3.2 Creating IM and IME Volumes	26
3.2.1 Creating an IM Volume	27
3.2.2 Creating an IME Volume	29
3.3 Creating a Second IM or IME Volume	29
3.4 Managing Hot Spares	30
3.5 Other Configuration Tasks	32
3.5.1 Viewing Volume Properties	32
3.5.2 Synchronizing an Array	32
3.5.3 Activating an Array	33
3.5.4 Deleting an Array	33
3.5.5 Locating a Disk Drive, or Multiple Disk Drives in a Volume	34
3.5.6 Selecting a Boot Disk	34
Chapter4 Overview of IntegratedStriping	37
4.1 Introduction	37
4.2 IS Features	38
4.3 IS Description	38
4.4 Integrated Striping Firmware	40
4.4.1 Metadata Support	40
4.4.2 SMART Support	40
4.4.3 Disk Write Caching	40
4.5 Fusion-MPT Support	40
Chapter5 Creating Integrated Striping Volumes	41
5.1 IS Configuration Overview	41
5.2 Creating IS Volumes	42
5.3 Creating a Second IS Volume	44
5.4 Other Configuration Tasks	45
5.4.1 Viewing IS Volume Properties	45
5.4.2 Activating an Array	45
5.4.3 Deleting an Array	46
5.4.4 Locating a Disk Drive, or Multiple Disk Drives in a Volume	46
5.4.5 Selecting a Boot Disk	47
AppendixA Using the CFGGEN IR Configuration Utility	49
A.1 Hardware and Software Requirements	50
A.2 CFGGEN Interface Description	51
A.3 CFGGEN Commands	51
A.3.1 Common Command Line Parameters	52
A.3.2 CREATE Command	53
A.3.3 DEFAULTS Command	54
A.3.4 DISPLAY Command	55
A.3.5 FORMAT Command	58
A.3.6 HOTSPARE Command	59
A.3.7 STATUS Command	60
A.3.8 SETOFFLINE Command	61
A.3.9 SETONLINE Command	62
A.3.10 AUTO Command (EFI Version Only)	63
A.3.11 DISABLEIR Command (EFI Version Only)	64
A.3.12 ENABLEIR Command (EFI Version Only)	65
A.3.13 LIST Command (EFI Version Only)	66