Asus Terminator Tualatin 786 MANUAL TERMINATOR TUALATIN English V1.0 - Page 55

ASUS Terminator Barebone System, CPU and Chassis Fan Connectors, IDE Activity LED 2-pin IDELED

Get Asus Terminator Tualatin PDF manuals and user guides View all Asus Terminator Tualatin manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

4. CPU and Chassis Fan Connectors The two 3-pin fan connectors (CPU_FAN, CHA_FAN) support cooling fans of 350mA (4.2 Watts) or less. Orient the fans so that the heat sink fins allow airflow to go across the onboard heat sink(s) instead of the expansion slots. The fan wiring and plug may vary depending on the fan manufacturer. The red wire should be positive while the black should be ground. Connect the fan plug to the board taking into consideration the polarity of the connector. NOTE: Use the "Rotation" signal only with a specially designed fan with a rotation signal. The Rotations Per Minute (RPM) can be monitored using ASUS PC Probe (see 4.2 Install the Operating System). WARNING! The CPU and/or motherboard will overheat if there is no airflow across the CPU and onboard heatsinks. Damage may occur to the motherboard and/or the CPU fan if these pins are incorrectly used. These are not jumpers, do not place jumper caps over these pins. TUSC CH_FAN ® GND +12V Rotation CPU_FAN GND +12V Rotation TUSC 12-Volt Cooling Fan Power 5. IDE Activity LED (2-pin IDELED) This connector supplies power to the cabinet's IDE activity LED. Read and write activity by devices connected to the Primary or Secondary IDE connectors cause the IDE LED to light up. TUSC ® TIP: If the case-mounted LED does not light, try reversing the 2-pin plug. IDELED TUSC IDE Activity LED ASUS Terminator Barebone System 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
ASUS Terminator Barebone System
55
4.
CPU and Chassis Fan Connectors
The two 3-pin fan connectors (CPU_FAN, CHA_FAN) support
cooling fans of 350mA (4.2 Watts) or less. Orient the fans so that
the heat sink fins allow airflow to go across the onboard heat
sink(s) instead of the expansion slots.
The fan wiring and plug
may vary depending on the fan manufacturer. The red wire should
be positive while the black should be ground. Connect the fan
plug to the board taking into consideration the polarity of the
connector.
NOTE:
Use the “Rotation” signal only with a specially designed fan
with a rotation signal. The Rotations Per Minute (RPM) can be
monitored using ASUS PC Probe (see
4.2 Install the Operating
System
).
5.
IDE Activity LED (2-pin IDELED)
This connector supplies power to the cabinet’s IDE activity LED.
Read and write activity by devices connected to the Primary or
Secondary IDE connectors cause the IDE LED to light up.
WARNING!
The CPU and/or motherboard will overheat if there is no airflow across
the CPU and onboard heatsinks.
Damage may occur to the
motherboard and/or the CPU fan if these pins are incorrectly used.
These are not jumpers, do not place jumper caps over these
pins.
TUSC
®
TUSC 12-Volt Cooling Fan Power
CH_FAN
CPU_FAN
GND
Rotation
+12V
GND
Rotation
+12V
TUSC
®
TUSC IDE Activity LED
TIP:
If the case-mounted LED does not
light, try reversing the 2-pin plug.
IDELED