Asus Terminator Tualatin 786 MANUAL TERMINATOR TUALATIN English V1.0 - Page 93

UART2 Use Standard Infrared [Disabled], Onboard Parallel Port [378H/IRQ7], Parallel Port Mode [ECP+

Get Asus Terminator Tualatin PDF manuals and user guides View all Asus Terminator Tualatin manuals
Add to My Manuals
Save this manual to your list of manuals

Page 93 highlights

Onboard FDC Swap A & B [No Swap] This field allows you to reverse the hardware drive letter assignments of your floppy disk drives. Configuration options: [No Swap] [Swap AB] Onboard FDC Smart FIFO [Disabled] Configuration options: [Enabled] [Disabled] Onboard Serial Port 1 [3F8H/IRQ4] Onboard Serial Port 2 [2F8H/IRQ3] These fields allow you to set the addresses for the onboard serial connectors. Serial Port 1 and Serial Port 2 must have different addresses. Configuration options: [3F8H/IRQ4] [2F8H/IRQ3] [3E8H/ IRQ4] [2E8H/IRQ10] [Disabled] UART2 Use Standard Infrared [Disabled] When enabled, this field activates the onboard standard infrared feature and sets the second serial UART to support the infrared module connector on the motherboard. If your system already has a second serial port connected to the onboard COM2 connector, it will no longer work if you enable the infrared feature. Configuration options: [Disabled] [Enabled] Onboard Parallel Port [378H/IRQ7] This field sets the address of the onboard parallel port connector. If you disable this feature, Parallel Port Mode and ECP DMA Select configurations will not be available. Configuration options: [Disabled] [378H/IRQ7] [278H/IRQ5] Parallel Port Mode [ECP+EPP] This field allows you to set the operation mode of the parallel port. [Normal] allows normal-speed operation but in one direction only; [EPP] allows bidirectional parallel port operation; [ECP] allows the parallel port to operate in bidirectional DMA mode; [ECP+EPP] allows normal speed operation in a two-way mode. Configuration options: [Normal] [EPP] [ECP] [ECP+EPP] ECP DMA Select [3] This field allows you to configure the parallel port DMA channel for the selected ECP mode. This selection is available only if you select [ECP] or [ECP+EPP] in Parallel Port Mode above. Configuration options: [1] [3] ASUS Terminator Barebone System 93

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
ASUS Terminator Barebone System
93
Onboard FDC Swap A & B [No Swap]
This field allows you to reverse the hardware drive letter assignments
of your floppy disk drives. Configuration options: [No Swap] [Swap
AB]
Onboard FDC Smart FIFO [Disabled]
Configuration options: [Enabled] [Disabled]
Onboard Serial Port 1 [3F8H/IRQ4]
Onboard Serial Port 2 [2F8H/IRQ3]
These fields allow you to set the addresses for the onboard serial
connectors. Serial Port 1 and Serial Port 2 must have different
addresses. Configuration options: [3F8H/IRQ4] [2F8H/IRQ3] [3E8H/
IRQ4] [2E8H/IRQ10] [Disabled]
UART2 Use Standard Infrared [Disabled]
When enabled, this field activates the onboard standard infrared
feature and sets the second serial UART to support the infrared
module connector on the motherboard. If your system already has a
second serial port connected to the onboard COM2 connector, it will
no longer work if you enable the infrared feature. Configuration
options: [Disabled] [Enabled]
Onboard Parallel Port [378H/IRQ7]
This field sets the address of the onboard parallel port connector.
If
you disable this feature,
Parallel Port Mode
and
ECP DMA Select
configurations will not be available. Configuration options: [Disabled]
[378H/IRQ7] [278H/IRQ5]
Parallel Port Mode [ECP+EPP]
This field allows you to set the operation mode of the parallel port.
[Normal] allows normal-speed operation but in one direction only;
[EPP]
allows bidirectional parallel port operation; [ECP]
allows the
parallel port to operate in bidirectional DMA mode; [ECP+EPP] allows
normal speed operation in a two-way mode. Configuration options:
[Normal] [EPP] [ECP] [ECP+EPP]
ECP DMA Select [3]
This field allows you to configure the parallel port DMA channel for
the selected
ECP
mode. This selection is available only if you select
[ECP] or [ECP+EPP] in
Parallel Port Mode
above. Configuration
options: [1] [3]