Asus V2-P5G33 User Manual - Page 40

Installing a floppy disk drive

Get Asus V2-P5G33 - V Series - 0 MB RAM PDF manuals and user guides
UPC - 610839743810
View all Asus V2-P5G33 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

2.10 Installing a floppy disk drive The system comes with one 3.25-inch drive bay for a floppy disk drive. To install a floppy disk drive: 1. Remove the drive slot metal plate cover. remove the metal plate cover and install the card reader module here 2. Carefully insert the floppy disk drive into the floppy drive bay until the screw holes align with the holes on the bay. 3. Secure the floppy disk drive with two screws on both sides. 3 3 2 4. Connect the floppy disk drive signal cable to the signal connector at the back of the drive. Power cable Floppy ribbon cable 5. Connect the other end of the signal cable to the floppy disk drive connector on the motherboard. See page 4-6 for the location of the floppy disk drive connector. 6. Connect a 4-pin power cable from the power supply unit to the power connector at the back of the floppy disk drive. 2-22 Chapter 2: Basic installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
2-22
Chapter 2: Basic installation
2.10
Installing a floppy disk drive
The system comes with one 3.25-inch drive bay for a floppy disk drive.
To install a floppy disk drive:
1.
Remove the drive slot metal plate cover.
2.
Carefully insert the floppy disk drive into the floppy drive bay until the
screw holes align with the holes on the bay.
3.
Secure the floppy disk drive with two screws on both sides.
4.
Connect the floppy disk drive signal cable to the signal connector at
the back of the drive.
5.
Connect the other end of the signal cable to the floppy disk drive
connector on the motherboard. See page 4-6 for the location of the
floppy disk drive connector.
6.
Connect a 4-pin power cable from the power supply unit to the power
connector at the back of the floppy disk drive.
Floppy ribbon
cable
Power cable
3
2
3
remove the metal
plate cover and
install the card
reader module
here