Audiovox APS95BT2 Programming Manual - Page 2

Programming Transmitters, To Program Additional Transmitters - program instructions

Get Audiovox APS95BT2 - Car - Code Learning Transmitter PDF manuals and user guides
UPC - 044476013294
View all Audiovox APS95BT2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

These factory programmed settings can be prioritized based on an individual's frequency of use, (i.e. pressing both buttons simultaneously to activate channel 1, arm/disarm etc.) by following the normal programming instructions below. Please note when changing the factory set button assignments, it is necessary to perform steps 5, 9, and 12 three times using "transmitter A", followed by one time using "transmitter B". PROGRAMMING TRANSMITTERS: It is important to remember that during programming, each individual step of the procedure must be executed within 15 seconds of the previous step. When the 15 second time limit is allowed to expire, the system will automatically exit program mode. This is indicated by a long "chirp" from the siren. Additionally, any time the ignition key is turned off while programming, the system will immediately exit program mode. This is also indicated by a long "chirp" from the siren. TO PROGRAM ADDITIONAL TRANSMITTERS: 1. Enter the vehicle, and turn the ignition key to the "on" position. 2. Move the valet/bypass switch on - off - on - off - on then off. 3. The dash LED will flash once, and the siren will "chirp" once, indicating the system is ready to accept programming for channel 1 or the arm/ disarm and panic functions. 4. You can assign any of the three transmitter button functions listed below to channel 1. a. Pressing button #1 on the keychain transmitter. b. Pressing button #2 on the keychain transmitter. c. Pressing both buttons simultaneously on the keychain transmitter. 5. Press and hold the selected choice a, b, or c above, until the siren emits a long "chirp" to confirm that programming of channel 1 was successful. 6. Move the valet/bypass switch on, then off again. 7. The dash mounted LED will flash 2 times, and the siren will "chirp" indicating that the system is ready to accept programming for channel 2, or the pulsed ground output for remote trunk release, remote car starter, etc. 8. You can assign any one of the two remaining button functions listed in 4a, 4b, or 4c above to operate channel 2. You cannot use the button(s) that operate channel 1, selected in step 5, to operate channel 2. 9. Press and hold the selected choice. The siren will emit a long "chirp" to confirm that programming of channel 2 was successful. 10. Move the valet/bypass switch on, then off again. 2 128 4624 2 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
128 4624
128 4624
128 4624
128 4624
128 4624
2
12
2
12
2
12
2
12
2
12
These factory programmed settings can be prioritized based on an individual's
frequency of use, (i.e. pressing both buttons simultaneously to activate
channel 1, arm/disarm etc.) by following the normal programming instructions
below.
Please note when changing the factory set button assignments, it is
necessary to perform steps 5, 9, and 12 three times using "transmitter A",
followed by one time using "transmitter B".
PROGRAMMING TRANSMITTERS:
It is important to remember that during programming, each individual step
of the procedure must be executed within 15 seconds of the previous step.
When the 15 second time limit is allowed to expire, the system will
automatically exit program mode.
This is indicated by a long "chirp" from the
siren.
Additionally, any time the ignition key is turned off while programming, the
system will immediately exit program mode.
This is also indicated by a long
"chirp"
from the siren.
TO PROGRAM ADDITIONAL TRANSMITTERS:
1.
Enter the vehicle, and turn the ignition key to the "on" position.
2.
Move the valet/bypass switch on - off - on - off - on then off.
3.
The dash LED will flash once, and the siren will "chirp" once, indicating
the system is ready to accept programming for channel 1 or the arm/
disarm and panic functions.
4.
You can assign any of the three transmitter button functions listed below
to channel 1.
a.
Pressing
button
#1 on the keychain transmitter.
b.
Pressing button #2 on the keychain transmitter.
c.
Pressing both buttons simultaneously on the keychain transmitter.
5.
Press and hold the selected choice a, b, or c above, until the siren emits
a long "chirp" to confirm that programming of channel 1 was successful.
6.
Move the valet/bypass switch on, then off again.
7.
The dash mounted LED will flash 2 times, and the siren will "chirp"
indicating that the system is ready to accept programming for channel
2, or the pulsed ground output for remote trunk release, remote car
starter, etc.
8.
You can assign any one of the two remaining button functions listed in
4a, 4b, or 4c above to operate channel 2.
You cannot use the button(s)
that operate channel 1, selected in step 5, to operate channel 2.
9.
Press and hold the selected choice.
The siren will emit a long "chirp" to
confirm that programming of channel 2 was successful.
10. Move the valet/bypass switch on, then off again.
2