Audiovox FRS1000 Owners Manual - Page 12

Transmit Power Selection Mode

Get Audiovox FRS1000 - FRS Base Station PDF manuals and user guides
UPC - 044476082191
View all Audiovox FRS1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

CTCSS filters out unwanted transmissions without the same coded squelch tone). To change the CTCSS Sub-channel, - From the FRS standby mode, press the MODE Button twice; the sub- channel number will flash as it is displayed. If oF is displayed, press the Up or Down button to enable the CTCSS mode; the CTC icon will appear steady on the display with the flashing sub-channel number. - Then press the Up or Down button to select the desired sub-channel for use. - Press the Power On/Off button momentarily to confirm selection. The CTCSS mode can be turned off by selecting the oF icon with the Up or Down button. NOTE: To communicate with other FRS units, they must be switched to the same channel and CTCSS subcode. To communicate with other FRS units that do not have subcodes, switch your unit to the same channel with the subcode set to oF. The CTCSS subcodes do not prevent others from hearing your transmission. This will only allow you to ignore all traffic on a given channel not using the same subcode. Transmit Power Selection Mode This feature permits selection of the transmitting power level at high or low. When set to low, the transmit range of the unit will be less; however, battery life will be increased. To access the transmitter power selection function: - Press the Mode Button 3 times until the Po icon appears with a flashing HI or Lo indication on the display. - Press the Up or Down button to toggle between the High and Low selections. - Momentarily press the Power Button to confirm selection. The display will indicate the current setting in standby mode. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
12
CTCSS filters out unwanted transmissions without the same coded squelch
tone).
To change the CTCSS Sub-channel,
- From the FRS standby mode, press the MODE Button twice; the sub-
channel number will flash as it is displayed.
If
oF
is displayed, press
the Up or Down button to enable the CTCSS mode; the
CTC
icon will
appear steady on the display with the flashing sub-channel number.
- Then press the Up or Down button to select the desired sub-channel
for use.
- Press the Power On/Off button momentarily to confirm selection.
The CTCSS mode can be turned off by selecting the
oF
icon with the Up or
Down button.
NOTE:
To communicate with other FRS units, they must be switched to
the same channel and CTCSS subcode. To communicate with other
FRS units that do not have subcodes, switch your unit to the same
channel with the subcode set
to
oF
.
The CTCSS subcodes do not prevent others from hearing your
transmission.
This will only allow
you
to ignore all traffic on a
given channel not using the same subcode.
Transmit Power Selection Mode
This feature permits selection of the transmitting power level at high or
low. When set
to low, the transmit range of the unit will be less; however,
battery life will be increased.
To access the transmitter power selection function:
-
Press the Mode Button 3 times until the
Po
icon appears with a flashing
HI
or
Lo
indication on the display.
-
Press the Up or Down button to toggle between the High and Low
se-
lections.
-
Momentarily press the Power Button to confirm selection.
The display will indicate the current setting in standby mode.