Audiovox NVX225 User Manual - Page 38

Start, Route To, Add Via, Remove Via, Continue, insert a stopover

Get Audiovox NVX225 - 3.5inch Touch Screen Jensen Portable Navigation PDF manuals and user guides
UPC - 689076576284
View all Audiovox NVX225 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

POIs nearby) appears near the selected map point if Popup Info is enabled in the Quick menu (4.7.2.4). If you do not use the Cursor menu in a few seconds, it will automatically vanish back to the bottom of the screen, and Popup Info disappears, too. You can have them reappear by reopening the Cursor menu using the arrow in the bottom right corner. When you open the menu manually, it will stay on until you close it or switch to another screen. Tip: If you want to see the map around the Cursor, close the Cursor menu and reopen it. When this menu is opened manually, the map is always moved to have the cursor in the centre. The content of the Cursor menu depends on the screen (Map or Cockpit) and it is slightly different if there is an active route already planned. You have the following options: • Start: use the Cursor as the departure point for your route. This menu point is available only in Map mode and when there is no active route. In Cockpit mode the departure point of the route is always the GPS position or if it is not available, the last known GPS position. • Route To: use the Cursor as the destination of your route. This button is to start a new route. The previous route (if it exists) will be deleted and replaced. If a multi-point route is active, The NVX225 Navigator will ask you whether you really want to delete it together with all its via points. • Add Via: by inserting the selected map point as a via, you instruct The NVX225 Navigator to cross this location before the destination of the route. This is the way to build a multi-point route in reverse order (when you wish to insert a stopover 'go to A but first get some fuel at B' or want to influence the direction of the route). This menu point works only if a route is already active. • Remove Via: removes the 'via point' near or at the Cursor. The route will be recalculated immediately excluding the deleted point. This menu point replaces Add Via and is available only if the Cursor is near or at a via point. • Continue: add a new destination to be reached after the previous destination. The new destination replaces the old one, which is now demoted to a via 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
38
POIs nearby) appears near the selected map point if Popup Info is enabled in the
Quick menu (4.7.2.4).
If you do not use the Cursor menu in a few seconds, it will automatically vanish back
to the bottom of the screen, and Popup Info disappears, too. You can have them
reappear by reopening the Cursor menu using the arrow in the bottom right corner.
When you open the menu manually, it will stay on until you close it or switch to
another screen.
Tip: If you want to see the map around the Cursor, close the Cursor menu and
reopen it. When this menu is opened manually, the map is always moved to have the
cursor in the centre.
The content of the Cursor menu depends on the screen (Map or Cockpit) and it is
slightly different if there is an active route already planned. You have the following
options:
•
Start:
use the Cursor as the departure point for your route. This menu point is
available only in Map mode and when there is no active route. In Cockpit
mode the departure point of the route is always the GPS position or if it is not
available, the last known GPS position.
•
Route To:
use the Cursor as the destination of your route. This button is to
start a new route. The previous route (if it exists) will be deleted and replaced.
If a multi-point route is active, The NVX225 Navigator will ask you whether you
really want to delete it together with all its via points.
•
Add Via:
by inserting the selected map point as a via, you instruct The
NVX225 Navigator to cross this location before the destination of the route.
This is the way to build a multi-point route in reverse order (when you wish to
insert a stopover ‘
go to A but first get some fuel at B
’ or want to influence the
direction of the route). This menu point works only if a route is already active.
•
Remove Via:
removes the ‘via point’ near or at the Cursor. The route will be
recalculated immediately excluding the deleted point. This menu point
replaces Add Via and is available only if the Cursor is near or at a via point.
•
Continue:
add a new destination to be reached after
the previous destination.
The new destination replaces the old one, which is now demoted to a via