Behringer DDM4000 Manual - Page 6

Stereo channels 1 - 4, Microphone channel - mixer

Get Behringer DDM4000 PDF manuals and user guides View all Behringer DDM4000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

6 DIGITAL PRO MIXER DDM4000 User Manual 2.1 Stereo channels 1 - 4 2.2 Microphone channel (2) (1) (11) (12) (3) (13) (5) (16) (4) (14) (17) (6) (18) (19) (15) (7) (9) Fig. 2.2: Microphone channel (8) (10) Fig. 2.1: Stereo channel strips (1) The input select switch lets you switch between two signal sources. Select Line to hear the signal of the Line input (67). Select Phono/Line to listen to the incoming source signal at the Phono/Line (68) input. (2) The GAIN knob adjusts the level of the input signal. The actual level is displayed on the level meter (3). (3) The 7-segment LED meter indicates the level of the input signal. (4) Each input channel features a 3-band equalizer (HIGH, MID and LOW) with kill feature, giving you up to 12 dB of boost and a maximum cut of -∞ dB (kill). The kill feature lets you mute the given frequency range. When each EQ knob is turned fully left, the signal is effectively muted. All EQ parameters can be adjusted in Channel Setup. (5) The MODE push button changes the functionality of the preset push button (6) from Multi to Single. (6) The preset push buttons P1, P2 and P3 allow you to store and activate equalizer presets. When activated in Single Mode, these push buttons provide a maximum cut of -∞ dB (kill function). (7) Press the PFL push button to listen in on the channel's signal using headphones. (8) The fader controls the channel volume. (9) The CURVE switch adjusts the response of the fader. In SOFT Mode, the fader responds slower to steady fader movement in the upper range and quicker in the lower range. In Sharp Mode, the fader adjusts the volume quicker in the upper third and slower in the lower range. In MID Mode, the fader responds in a linear fashion. Since a difference in volume levels is heard when switching between modes, don't use this switch while playing music! (10) The CF ASSIGN push button lets you determine on which side of the crossfader (20) (A or B the signal is to be heard. (11) The GAIN knob adjusts the level of the microphone signal at the MIC 1 input. (12) This switch determines which signal is to be displayed on the level meter (13). IN VU shows the unprocessed input level which helps you to adjust the microphone signal correctly. XMC VU shows the level after it has passed the Ultramic processor. (13) The 7-segment LED meter indicates the level of the microphone channel. (14) The microphone channel strip features a 3-band equalizer (HIGH, MID and LOW). The range is +/-12 dB. (15) The ON/OFF push button turns the microphone channel on and off. (16) The MIC SETUP push button opens the Mic Setup menu on the display. This allows you to adjust the settings of the equalizer, the Ultramic processor and the MIC FX (effects processor). (17) The XMC ON push button activates the ULTRAMIC processor, which includes a 2-band compressor and expander. Ultramic settings can be adjusted in Mic Setup. (18) The MIC FX ON push button activates the microphone effects processor. Select the effect in Mic Setup. (19) The TALK ON push button activates the Talkover function. This attenuates the volume level of the music as soon as you speak into the microphone. This is a very useful function to make yourself heard over the music being played. You can adjust all the relevant settings in Talk Setup.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
6
DIGITAL PRO MIXER DDM4000 User Manual
2.1
Stereo channels 1 – 4
(4)
(1)
(3)
(5)
(6)
(9)
(10)
(7)
(8)
(2)
Fig. 2.1: Stereo channel strips
(1)
The input select switch lets you switch between two signal sources.
Select Line to hear the signal of the Line input
(67)
. Select Phono/Line to
listen to the incoming source signal at the Phono/Line
(68)
input.
(2)
The
GAIN
knob adjusts the level of the input signal. The actual level
is displayed on the level meter
(3)
.
(3)
The 7-segment LED meter indicates the level of the input signal.
(4)
Each input channel features a 3-band equalizer
(HIGH, MID and LOW)
with kill feature, giving you up to 12 dB of boost and a maximum cut
of -
∞
dB (kill). The kill feature lets you mute the given frequency range.
When each EQ knob is turned fully left, the signal is effectively muted.
All EQ parameters can be adjusted in
Channel Setup.
(5)
The
MODE
push button changes the functionality of the preset push button
(6)
from Multi to Single.
(6)
The preset push buttons
P1, P2
and
P3
allow you to store and activate
equalizer presets. When activated in Single Mode, these push buttons
provide a maximum cut of -
∞
dB (kill function).
(7)
Press the
PFL
push button to listen in on the channel’s signal
using headphones.
(8)
The fader controls the channel volume.
(9)
The
CURVE
switch adjusts the response of the fader. In
SOFT
Mode, the fader
responds slower to steady fader movement in the upper range and quicker in
the lower range. In
Sharp
Mode, the fader adjusts the volume quicker in the
upper third and slower in the lower range. In
MID
Mode, the fader responds
in a linear fashion. Since a difference in volume levels is heard when
switching between modes, don’t use this switch while playing music!
(10)
The
CF ASSIGN
push button lets you determine on which side of the
crossfader
(20)
(A or B the signal is to be heard.
2.2
Microphone channel
(11)
(12)
(13)
(16)
(17)
(18)
(19)
(14)
(15)
Fig. 2.2: Microphone channel
(11)
The
GAIN
knob adjusts the level of the microphone signal at the MIC 1 input.
(12)
This switch determines which signal is to be displayed on the level meter
(13)
.
IN VU
shows the unprocessed input level which helps you to adjust the
microphone signal correctly.
XMC VU
shows the level after it has passed
the Ultramic processor.
(13)
The 7-segment LED meter indicates the level of the microphone channel.
(14)
The microphone channel strip features a 3-band equalizer
(HIGH, MID and LOW)
. The range is +/-12 dB.
(15)
The
ON/OFF
push button turns the microphone channel on and off.
(16)
The
MIC SETUP
push button opens the Mic Setup menu on the display.
This allows you to adjust the settings of the equalizer, the Ultramic processor
and the MIC FX (effects processor).
(17)
The
XMC ON
push button activates the ULTRAMIC processor, which includes
a 2-band compressor and expander. Ultramic settings can be adjusted in
Mic Setup.
(18)
The
MIC FX ON
push button activates the microphone effects processor.
Select the effect in
Mic Setup
.
(19)
The
TALK ON
push button activates the Talkover function. This attenuates
the volume level of the music as soon as you speak into the microphone.
This is a very useful function to make yourself heard over the music
being played. You can adjust all the relevant settings in
Talk Setup.