Beko DIN15X10 User Manual - Page 30

End of programme

Get Beko DIN15X10 PDF manuals and user guides View all Beko DIN15X10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Operating the product Rinse Aid indicator ( ) Please check the rinse aid indicator on the display to see whether there is adequate amount of rinse aid in the dishwasher or not. You need to refill the rinse aid reservoir with rinse aid whenever rinse aid indicator appears on the display of your machine. End of programme C When the programme you have selected comes to an end, an audible warning signal will warn you to turn off your machine. This audible signal will warn you with certain intervals before it turns off. End of Programme indicator will light up when the washing programme is over. 1. Open the door of the machine. 2. Press On/Off key to turn off your machine. 3. Close the tap. 4. Unplug the machine from the socket. C For energy saving, the machine is automatically turned off following the completion of the programme or if the programme is not started. C Leave your dishes in the machine for about 15 minutes to allow them cool down after they are washed. Your dishes will dry in a shorter time if you leave the door of your machine ajar during this period. This process will increase the drying effectiveness of your machine. Water cut-off warning If mains water is cut or water inlet tap is turned off the machine cannot take water in and P2 icon will flash on the programme indicator. As long as the problem continues, washing programme is paused and the water inlet is checked regularly by the machine; when the water is restored P2 icon will disappear after a while and the washing programme resumes. Overflowing warning If the machine intakes too much water or there is leakage at any of the components then the machine will detect this and P1 icon will flash on the Programme indicator. As long as the overflowing continues safety algorithm will be active and try to discharge the water. If overflowing stops and safety is assured, P1 icon will disappear. If P1 does not disappear, there is a permanent fault. In this case the authorised service should be contacted. 28 /41 EN Dishwasher / User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
28
Dishwasher / User’s Manual
/41 EN
Operating the product
R±nse A±d ±nd±cator (
)
Please check the rinse aid indicator on the
display to see whether there is adequate
amount of rinse aid in the dishwasher or
not. You need to refill the rinse aid reservoir
with rinse aid whenever rinse aid indicator
appears on the display of your machine.
End of programme
C
When the programme you have
selected comes to an end, an
audible warning signal will warn
you to turn off your machine.
This audible signal will warn you
with certain intervals before it
turns off.
End of Programme indicator will light up
when the washing programme is over.
1.
Open the door of the machine.
2.
Press On/Off key to turn off your
machine.
3.
Close the tap.
4.
Unplug the machine from the socket.
C
For energy saving, the machine
is automatically turned off
following the completion of the
programme or if the programme
is not started.
C
Leave your dishes in the
machine for about 15 minutes
to allow them cool down after
they are washed. Your dishes
will dry in a shorter time if you
leave the door of your machine
ajar during this period. This
process will increase the drying
effectiveness of your machine.
Water cut-off warn±ng
If mains water is cut or water inlet tap is
turned off the machine cannot take water
in and P2 icon will flash on the programme
indicator. As long as the problem continues,
washing programme is paused and the
water inlet is checked regularly by the
machine; when the water is restored P2
icon will disappear after a while and the
washing programme resumes.
Overflow±ng warn±ng
If the machine intakes too much water or
there is leakage at any of the components
then the machine will detect this and P1
icon will flash on the Programme indicator.
As long as the overflowing continues
safety algorithm will be active and try
to discharge the water. If overflowing
stops and safety is assured, P1 icon will
disappear. If P1 does not disappear, there
is a permanent fault. In this case the
authorised service should be contacted.