Beltronics BEL 990 Owner's Manual - Page 7

Reset to Factory Settings, Voltage Warning, Bright/Dim/Dark Button, Auto-Mute/Volume Control Button - international radar detector

Get Beltronics BEL 990 PDF manuals and user guides View all Beltronics BEL 990 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Reset to Factory Settings You can reset your unit to factory settings for start-up mode, volume, drk, aud, cty, Travel Mode and Selectable Features. To reset, press and hold the cty button until the display shows "RESET". Two "beeps" will sound and your unit will be on and ready for operation. Voltage Warning BEL 990 International continually checks your vechicle's voltage to ensure proper performance of the detector. The unit's operating range is 10.5 to 16.0 volts. If voltage is above 10.5, the display will flash"HI VOLT" until condition is rectified. If voltage falls below 10.5 volts, display will flash"LOW VOLT" until condition is rectified. drk (Bright/Dim/Dark) Button The drk button allows selection of a bright, fully adjustable dim mode or dark mode. The unit is factory preset to full bright display. To engage dim mode, press and hold the drk button. The display will cycle through various levels of dim illumination. Release the button at your chosen level. To engage dark mode, press the drk button a second time. A single "beep" coupled with the brief illumination of "DARK" on the display confirms your selection. You'll notice an "H" (Highway mode) or "C" (City mode) remains dim to confirm your unit is receiving power. To return to a full bright setting, press the drk button a third time; two "beeps" confirm this selection. Use of the drk button does not affect audio alerts. Important-if you press the the drk button and do not receive audible confirmation, the audio level has been set too low. aud (Auto-Mute/Volume Control) Button Manual Muting of Audio Alerts (Radar and sws™) Whether Auto-Mode is selected on or off in Selectable Features the audio alerts can be completely muted by 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
Reset to Factory Settings
You can reset your unit to factory settings for start-up mode,
volume,
drk, aud, cty
, Travel Mode and Selectable Features. To
reset, press and hold the
cty
button until the display shows
“
RESET
”. Two “beeps” will sound and your unit will be
on
and
ready for operation.
Voltage Warning
BEL 990
International
continually checks your vechicle’s voltage
to ensure proper performance of the detector. The unit’s
operating range is 10.5 to 16.0 volts. If voltage is above 10.5, the
display will flash “
HI VOLT
” until condition is rectified. If voltage
falls below 10.5 volts, display will flash “
LOW VOLT
” until
condition is rectified.
drk
(Bright/Dim/Dark) Button
The
drk
button allows selection of a bright, fully adjustable
dim mode or dark mode. The unit is factory preset to full
bright display. To engage
dim
mode, press and hold the
drk
button. The display will cycle through various levels of dim
illumination. Release the button at your chosen level. To
engage dark mode, press the
drk
button a second time. A
single “beep” coupled with the brief illumination of “
DARK
”
on the display confirms your selection.You’ll notice an “
H
”
(Highway mode) or “
C
” (City mode) remains dim to confirm
your unit is receiving power.To return to a full bright setting,
press the
drk
button a third time; two “beeps” confirm this
selection. Use of the
drk
button does not affect audio alerts.
Important—if you press the the
drk
button and do not receive
audible confirmation, the audio level has been set too low.
aud
(Auto-Mute/Volume Control) Button
Manual Muting of Audio Alerts (Radar and
sws
™
)
Whether Auto-Mode is selected
on
or
off
in Selectable
Features the audio alerts can be completely muted by