BenQ 0.6 Wall Mount-WM06G3 Wall Mount User Manual - Page 6

Installation Steps

Get BenQ 0.6 Wall Mount-WM06G3 PDF manuals and user guides View all BenQ 0.6 Wall Mount-WM06G3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

English Installation Steps A 1. Installing the wall bracket A. Make sure the wall bracket (P) is in the correct position on the wall. Hold the bracket (P) rmly against the wall and mark the places for the holes with a pencil. Drill the holes at the marked points. The holes for a P masonry wall should be 10mm (0.39") in diameter and 55mm deep (2.17"). Use a hammer to drive the plastic plugs (C) into the holes. For a wooden wall, drill 4.5mm (0.17") diameter holes 55m (2.17") deep. B B. Screw the self-tapping screws (C) into the wall. C. Push the power cord into the front end of the projector main support member and pull it out at the back. D. Insert and secure the socket head screw M6 x L8 (F) in P the holes of the projector main support member (Q) and the wall bracket (P) by using a 5mm hex wrench (K). It is necessary to leave a gap of 0.5mm for adjustment of the angle after assembly. E. Before positioning the hinge module (A), secure the socket head screw (H) in the projector main support member (Q) to enable the cantilever support to be in 1. the horizontal direction. A 2. Installing the xing bracket on the bottom of the projector A. Install the projector bracket (A) on the projector, using shim screws (I) and sleeves (J) to fasten these 3 parts onto the projector. J B. Align the holes in the hinge connector (D) with those in the hinge module (A). Insert M6 x L10 (F) hex head screws into the holes and tighten them with Wrenches (K). Allow 2-3mm clearance for installing the bracket on the arm. 2. A A 3. Installing the bracket on the bottom of the projector arm A. Assemble the hinge module (A) and the projector main support member (Q). B. After attaching the projector bracket (A) to chassis (Q), tighten both with a wrench (L). 3. A 4. Cable Management A. Plug the power cord into the projector. B. Fit the plastic cap (M) to the end of the projector main support member (Q). C. Pass the power cord through the lower plastic cover (O) and then t the upper (N) and lower (O) plastic covers as shown. C C C Q D D F Q B A I 0.5mm E G K E F H L B Q L BM N O O 6 Installation Steps 4.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
6
Installation Steps
Installation Steps
B
C
D
E
1.
2.
3.
4.
D
P
I
J
A
C
P
A
O
Q
B
A
Q
F
K
F
H
0.5mm
B
A
C
Q
A
G
E
L
L
N
M
O
B
A
1. Installing the wall bracket
A.
Make sure the wall bracket (P) is in the correct position
on the wall. Hold the bracket (P) firmly against the wall
and mark the places for the holes with a pencil.
Drill the holes at the marked points. The holes for a
masonry wall should be 10mm (0.39”) in diameter and
55mm deep (2.17”). Use a hammer to drive the plastic
plugs (C) into the holes.
For a wooden wall, drill 4.5mm (0.17”) diameter holes
55m (2.17”) deep.
B.
Screw the self-tapping screws (C) into the wall.
C.
Push the power cord into the front end of the projector
main support member and pull it out at the back.
D. Insert and secure the socket head screw M6 x L8 (F) in
the holes of the projector main support member (Q)
and the wall bracket (P) by using a 5mm hex wrench
(K). It is necessary to leave a gap of 0.5mm for
adjustment of the angle after assembly.
E.
Before positioning the hinge module (A), secure the
socket head screw (H) in the projector main support
member (Q) to enable the cantilever support to be in
the horizontal direction.
2. Installing the fixing bracket on the
bottom of the projector
A.
Install the projector bracket (A) on the projector, using
shim screws (I) and sleeves (J) to fasten these 3 parts
onto the projector.
B.
Align the holes in the hinge connector (D) with those in
the hinge module (A). Insert M6 x L10 (F) hex head
screws into the holes and tighten them with Wrenches
(K). Allow 2-3mm clearance for installing the bracket on
the arm.
3. Installing the bracket on the bottom of
the projector arm
A.
Assemble the hinge module (A) and the projector main
support member (Q).
B.
After attaching the projector bracket (A) to chassis (Q),
tighten both with a wrench (L).
4. Cable Management
A.
Plug the power cord into the projector.
B.
Fit the plastic cap (M) to the end of the projector main
support member (Q).
C.
Pass the power cord through the lower plastic cover (O)
and then fit the upper (N) and lower (O) plastic covers
as shown.
English