BenQ CP120 User Manual - Page 29

Using the projector, Start up - lamp

Get BenQ CP120 - XGA DLP Projector PDF manuals and user guides
UPC - 840046012915
View all BenQ CP120 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Using the projector Start up 1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). Check that the POWER indicator on the projector lights orange after power has been applied. 2. Slide open the lens cover. If it is left closed, it could become deformed due to heat. 3. Press and hold (for 2 seconds) the POWER button on the remote control or projector to start the unit. The POWER indicator light flashes green and stays green when the unit is on. The start up procedure takes about 30 seconds after pressing the POWER button In the later stage of start up, a default BenQ logo is projected. If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before energising the lamp. 4. If you are prompted for a password, press the arrow buttons to select the four password digits, then press the Auto (or AUTO/CH.) button. For information about the password function, refer to "Utilizing the password function" on page 22. 5. Switch all of the connected equipment on. 6. The current input source being scanned displays in the upper part of a dialog on the screen. The scan will continue until signal from the input source is detected. If the Auto Off function (See "Auto Off (Off)" on page 43 for details) is activated, the projector will turn off automatically if no input signal is detected from the selected source after the period of time as set by the Auto Off function. Using the projector 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
Using the projector
21
Using the projector
Start up
If the projector is still hot from previous activity, it will run the cooling fan for approximately 90
seconds before energising the lamp.
4.
If you are prompted for a password, press the arrow buttons to select the four
password digits, then press the
Auto
(or
AUTO/CH.
) button. For information about
the password function, refer to
"Utilizing the password function" on page 22
.
5.
Switch all of the connected equipment on.
6.
The current input source being scanned displays in the upper part of a dialog on the
screen. The scan will continue until signal from the input source is detected.
If the Auto Off function (See
"Auto Off (Off)" on page 43
for details) is activated, the projector
will turn off automatically if no input signal is detected from the selected source after the
period of time as set by the Auto Off function.
1.
Plug the power cord into the projector and
into a wall socket. Turn on the wall socket
switch (where fitted). Check that the
POWER
indicator on the projector lights
orange after power has been applied.
2.
Slide open the lens cover. If it is left closed,
it could become deformed due to heat.
3.
Press and hold (for 2 seconds) the
POWER
button on the remote control or projector
to start the unit. The
POWER
indicator
light flashes green and stays green when the
unit is on.
The start up procedure takes about 30
seconds after pressing the
POWER
button
In the later stage of start up, a default BenQ
logo is projected.