BenQ MX717 DLP Projector User Manual - Page 19

Operation, Starting up the projector

Get BenQ MX717 DLP Projector PDF manuals and user guides View all BenQ MX717 DLP Projector manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Operation Starting up the projector 1. Plug the power cord into the projector and into a power outlet. Turn on the power outlet switch (where fitted). Check that the POWER indicator light on the projector lights orange after power has been applied. Please use the original accessories (e.g. power cord) only with the device to avoid possible dangers such as electric shock and fire. MX716 2. Press POWER or ON to start the projector. As soon as the lamp lights up, a "Power MX717 On Tone" will be heard. The POWER indicator light flashes green and stays green when the projector is on. The start up procedure takes about 30 seconds. In the later stage of start up, a startup logo is projected. (If necessary) Rotate the focus ring to adjust the image clearness. To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 35 for details. If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before energizing the lamp. 3. If the projector is activated for the first time, select your OSD language following the onscreen instructions. 4. If you are prompted for a password, press the arrow keys to enter a six-digit password. See "Utilizing the password function" on page 23 for details. 5. Switch all of the connected equipment on. 6. The projector will start to search for input signals. The current input signal being scanned displays in the upper left corner of the screen. If the projector doesn't detect a valid signal, the message "No Signal" will continue displaying until an input signal is found. You can also press SOURCE on the projector or remote control to select your desired input signal. See "Switching input signal" on page 26 for details. If the frequency/resolution of the input signal exceeds the projector's operating range, you will see the message "Out of Range" displayed on a blank screen. Please change to an input signal which is compatible with the projector's resolution or set the input signal to a lower setting. See "Timing chart" on page 62 for details. Downloaded From projector-manual.com BenQ Manuals Operation 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
Operation
19
Operation
Starting up the projector
1.
Plug the power cord into the projector and into a
power outlet. Turn on the power outlet switch
(where fitted). Check that the
POWER indicator
light
on the projector lights orange after power
has been applied.
Please use the original accessories (e.g. power cord) only with the
device to avoid possible dangers such as electric shock and fire.
2.
Press
POWER
or
ON
to start the
projector. As soon as the lamp lights up, a "
Power
On Tone
" will be heard. The
POWER indicator
light
flashes green and stays green when the
projector is on.
The start up procedure takes about 30 seconds. In
the later stage of start up, a startup logo is
projected.
(If necessary) Rotate the focus ring to adjust the image clearness.
To turn off the ring tone, see
"Turning off the Power On/Off Ring Tone" on page 35
for details.
If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds
before energizing the lamp.
3.
If the projector is activated for the first time,
select your OSD language following the on-
screen instructions.
4.
If you are prompted for a password, press the
arrow keys to enter a six-digit password. See
"Utilizing the password function" on page 23
for
details.
5.
Switch all of the connected equipment on.
6.
The projector will start to search for input
signals. The current input signal being scanned
displays in the upper left corner of the screen. If
the projector doesn't detect a valid signal, the message “No Signal” will continue
displaying until an input signal is found.
You can also press
SOURCE
on the projector or remote control to select your
desired input signal. See
"Switching input signal" on page 26
for details.
If the frequency/resolution of the input signal exceeds the projector's operating range, you will see the
message “Out of Range” displayed on a blank screen. Please change to an input signal which is compatible with
the projector's resolution or set the input signal to a lower setting. See
"Timing chart" on page 62
for details.
MX716
MX717
Downloaded From projector-manual.com BenQ Manuals