Biostar TA990FXE Setup Manual - Page 3

Introduction - drivers

Get Biostar TA990FXE PDF manuals and user guides View all Biostar TA990FXE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

CHAPTER 1: INTRODUCTION TA990FXE 1.1 BEFORE YOU START Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below: „ Prepare a dry and stable working environment with sufficient lighting. „ Always disconnect the computer from power outlet before operation. „ Before you take the motherboard out from anti-static bag, ground yourself properly by touching any safely grounded appliance, or use grounded wrist strap to remove the static charge. „ Avoid touching the components on motherboard or the rear side of the board unless necessary. Hold the board on the edge, do not try to bend or flex the board. „ Do not leave any unfastened small parts inside the case after installation. Loose parts will cause short circuits which may damage the equipment. „ Keep the computer from dangerous area, such as heat source, humid air and water. „ The operating temperatures of the computer should be 0 to 45 degrees Celsius. 1.2 PACKAGE CHECKLIST Serial ATA Cable X4 Rear I/O Panel for ATX Case X 1 User's Manual X1 Fully Setup Driver CD X1 CFX Bridge X2 Note: The package contents may be different due to area or your motherboard version. 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
TA990FXE
1
CHAPTER 1: INTRODUCTION
1.1
B
EFORE
Y
OU
S
TART
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
Prepare a dry and stable working environment with
sufficient lighting.
Always disconnect the computer from power outlet
before operation.
Before you take the motherboard out from anti-static
bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.
Avoid touching the components on motherboard or the
rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.
Do not leave any unfastened small parts inside the
case after installation. Loose parts will cause short
circuits which may damage the equipment.
Keep the computer from dangerous area, such as heat
source, humid air and water.
The operating temperatures of the computer should be
0 to 45 degrees Celsius.
1.2
P
ACKAGE
C
HECKLIST
Serial ATA Cable X4
Rear I/O Panel for ATX Case X 1
User’s Manual X1
Fully Setup Driver CD X1
CFX Bridge X2
Note:
The package contents may be different due to area or your motherboard version.