Bosch LTC 5136/61 Instruction Manual - Page 13

Setting Fast Address, Feature - autodome controller manual

Get Bosch LTC 5136/61 PDF manuals and user guides View all Bosch LTC 5136/61 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

LTC 5136 Series | Instruction Manual | Setting Fast Addess Feature EN | 13 4.5 AutoDome Camera or Receiver/Driver Site Configuration Follow the standard installation instructions provided with the AutoDome Camera or Allegiant Series Receiver/Driver unit to connect the data cable to the unit. Set the address of the AutoDome camera or receiver/driver, to the camera number that will be selected on the Controller keypad. AutoDome cameras also support address setting via the on-screen menu Fast Address feature. The next section outlines setting of the AutoDome's Fast Address. • ON-998-ENTER causes all cameras, regardless of Fast address status, to enter the addressing mode. Video signals from the camera site are NOT connected to the Controller. The video signal(s) from the camera site(s) should be connected to an appropriate viewing monitor or other video processing equipment (switcher, multiplexer, etc.). 5 SETTING FAST ADDRESS FEATURE Use the AutoDome's Fast Address feature to set the AutoDome address via the controller and on-screen menus instead of using the switch address (thumbwheel). Fast Address can also be used to change addresses, even if the thumbwheel switch is set. Figure FA1 3. Press ON-26-ENTER. The screen shown in FIGURE FA2 will be displayed. At this point, any camera whose ID does not begin with 26 will exit the Fast Addressing mode. The following is an example of how to Fast Address an AutoDome (ID number 26636, logical camera #3). The AutoDome being Fast Addressed has the switch address (thumbwheel) set to 0. 1. Call up the camera to the screen you are viewing (i.e. CAMERA-3-ENTER). 2. Press ON-999-ENTER. The screen shown in FIGURE FA1 is displayed. • Any camera without a Fast Address will display the screen in FIGURE FA1 when the ON-999-ENTER is used. Make sure you are viewing the camera that you want to program. Figure FA2 4. Press ON-636-ENTER. The screen shown in FIGURE FA3 is displayed. At this point, Camera ID 26636 will be the only camera in the Fast Addressing mode. • If the camera's Fast Address is the same as the keyboard address, ON-999-ENTER will make the camera enter the Fast Address mode. This is required to change or disable a Fast Address. Bosch Security Systems | 04 September 2003 Figure FA3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
LTC 5136 Series |
Instruction Manual
|
Setting Fast Addess Feature
Bosch Security Systems | 04 September 2003
EN
|
13
4.5
AutoDome Camera or
Receiver/Driver Site Configuration
Follow the standard installation instructions provided
with the AutoDome Camera or Allegiant Series
Receiver/Driver unit to connect the data cable to the
unit. Set the address of the AutoDome camera or
receiver/driver, to the camera number that will be
selected on the Controller keypad. AutoDome cameras
also support address setting via the on-screen menu
Fast Address
feature. The next section outlines setting of
the AutoDome’s
Fast Address
.
Video signals from the camera site are NOT connected
to the Controller. The video signal(s) from the camera
site(s) should be connected to an appropriate viewing
monitor or other video processing equipment (switcher,
multiplexer, etc.).
5
SETTING FAST ADDRESS
FEATURE
Use the AutoDome’s
Fast Address
feature to set the
AutoDome address via the controller and on-screen
menus instead of using the switch address
(thumbwheel).
Fast Address
can also be used to change
addresses, even if the thumbwheel switch is set.
The following is an example of how to
Fast Address
an
AutoDome (ID number 26636, logical camera #3).
The AutoDome being
Fast Addressed
has the switch
address (thumbwheel) set to 0.
1.
Call up the camera to the screen you are
viewing (i.e.
CAMERA-3-ENTER
).
2. Press
ON-999-ENTER
. The screen shown in
FIGURE FA1 is displayed.
•
Any camera without a
Fast Address
will
display the screen in FIGURE FA1 when
the
ON-999-ENTER
is used. Make sure you
are viewing the camera that you want to
program.
•
If the camera’s
Fast Address
is the same as the
keyboard address,
ON-999-ENTER
will
make the camera enter the
Fast Address
mode. This is required to change or disable a
Fast Address
.
•
ON-998-ENTER
causes all cameras,
regardless of
Fast address
status, to enter the
addressing mode.
Figure FA1
3. Press
ON-26-ENTER
. The screen shown in
FIGURE FA2 will be displayed. At this point,
any camera whose ID does not begin with
26
will exit the
Fast Addressing
mode.
Figure FA2
4. Press
ON-636-ENTER
. The screen shown in
FIGURE FA3 is displayed. At this point,
Camera ID 26636 will be the only camera in
the
Fast Addressing
mode.
Figure FA3