Bosch NGT745UC Installation Instructions - Page 5

Installation - stainless steel gas cooktop

Page 5 highlights

Installation Before You Begin Tools and Parts Needed Parts Included Cabinet Requirements 1. Phillips Head Screwdriver 2) Drill with 1/4" (6.35mm) bit 3) Tape Measure 1) Foam tape 2) Hold down brackets (4) 3) Screws, #10-32 x 2 1/2" (63.8mm) (4) 4) Sheet Metal Screws, #8 x 3/8" (9.5mm) (4) 5) Washers (4) 6) Rubber Grate Foot (1 extra foot is included for future use if required) If parts are missing or damaged, call the number or write to the address listed inside the back cover. Dimension requirements in Figs. 1 & 2 are for combustible surfaces. When the surface is protected by a material listed by UL as a Floor Protector and Wall Shield covered with not less than No. 28 MSG sheet metal 0.015 inch (0.38mm) stainless steel, 0.024 inch (0.6mm) aluminum or copper, it is considered noncombustible and some dimensions may be reduced. For a noncombustible surface over the cooktop, the minimum clearance is 24" (61cm) rather than 30" (76cm) . • Instructions are based on standard American cabinets 36" high (91cm) x 24" deep (61cm) with a 25" (63cm) countertop. • Provide approximately a 10 square inch opening (65cm2) in the toe kick area or other cabinet area for adequate air inlet to the cabinet. Figure 1 - Installed Dimensions (from cooktop edges) Depth from Back Wall Cabinet 13" (33cm) max. Hood Depth - 24" (61cm) max. Above Counter - 30" (76 cm) min. to Combustible Surface NGT(P)7x - 30" (76cm) min. NGT(P)9x - 36" (91cm) min. 18" (46cm) min. Left Side 6" (15cm) min. Centered Over Cooktop Rear Wall - 1-3/4"(4cm) Right Side 3" (8cm) min. NOTE: All measurements given have to be precisely followed. If nonstandard cabinets are used, make sure they are installed with minimum dimensions shown in fig. 1 and fig. 2. Plan the installation of the unit so that the power cord, gas shut-off valve and gas pressure regulator are accessible from the front of cabinet. If a drawer is installed directly under the cooktop, its depth (front to back) should be no greater than 15" (38cm). English 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28

English 3
Installation
Before You Begin
Tools and Parts Needed
1.
Phillips Head Screwdriver
2)
Drill with 1/4” (6.35mm) bit
3)
Tape Measure
Parts Included
1)
Foam tape
2)
Hold down brackets (4)
3)
Screws, #10-32 x 2 1/2” (63.8mm) (4)
4)
Sheet Metal Screws, #8 x 3/8” (9.5mm) (4)
5)
Washers (4)
6)
Rubber Grate Foot (1 extra foot is included for future use if required)
If parts are missing or damaged, call the number or write to the address listed
inside the back cover.
Cabinet Requirements
Dimension requirements in Figs. 1 & 2 are for combustible surfaces. When the
surface is protected by a material listed by UL as a Floor Protector and Wall
Shield covered with not less than No. 28 MSG sheet metal 0.015 inch (0.38mm)
stainless steel, 0.024 inch (0.6mm) aluminum or copper, it is considered noncom-
bustible and some dimensions may be reduced. For a noncombustible surface
over the cooktop, the minimum clearance is 24" (61cm) rather than 30" (76cm) .
Instructions are based on standard American cabinets 36" high (91cm) x 24"
deep (61cm) with a 25" (63cm) countertop.
Provide approximately a 10 square inch opening (65cm
2
) in the toe kick area
or other cabinet area for adequate air inlet to the cabinet.
Figure 1 - Installed Dimensions (from cooktop edges)
NOTE:
All measurements given have to be precisely followed. If nonstandard
cabinets are used, make sure they are installed with minimum dimensions shown
in fig. 1 and fig. 2.
Plan the installation of the unit so that the power cord, gas shut-off valve and gas
pressure regulator are accessible from the front of cabinet. If a drawer is installed
directly under the cooktop, its depth (front to back) should be no greater than 15"
(38cm).
Depth from Back Wall
Cabinet 13" (33cm) max.
Hood Depth - 24" (61cm) max.
Centered Over Cooktop
Rear Wall - 1-3/4"(4cm)
Right Side
3" (8cm) min.
Left Side
6" (15cm) min.
18" (46cm) min.
Above Counter - 30" (76 cm) min. to
Combustible Surface
NGT(P)7x - 30" (76cm) min.
NGT(P)9x - 36" (91cm) min.