Bosch SPX5ES55UC Installation Instructions - Page 6

max 18

Page 6 highlights

Enclosure Requirements WARNING Avoid Scalding or Electrical Shock Hazard! Make sure the water supply and electrical supply are shut off before installation or service. NOTE: This dishwasher is designed to be enclosed on the top and both sides by standard residential kitchen cabinetry. After locating the proper place for your new dishwasher, you will need to create any required openings to allow for passage of the water, drain and electrical line. In order to avoid interference with the dishwasher when sliding it into the cabinet, place your openings within the dimensions shown in Figure 3 below. Figure 3 Select a location as close to the sink as possible for easy access to water supply and drain lines. For proper dishwasher operation and appearance, ensure that the enclosure is square and has the dimensions shown in Figure 1 below. 32-341/2" (815-875mm) Figure 1 223 /5"(575mm) 1(7m457/a81xm0"1m(48)5"0mm) NOTE: If your dishwasher opening width measures >18 in (458 mm) use the TOP OR SIDE MOUNT mounting methods. If your dishwasher opening width measures 177/10 - 18 in (450 - 458 mm) use the ALTERNATE SIDE MOUNT mounting method. If the dishwasher is to be installed in a corner, make sure that there is adequate clearance to open the door. See Figure 2 below. 41/2" (114mm) 21/2" (64mm) Required Openings: 43/4″ x 23/8″ (120 x 60mm) - To pass the included electrical supply junction box through to adjacent cabinet. Note: If the incoming electric supply, water supply and drain connections are all in the same cabinet, the one 43/4″ x 23/8″ (120 x 60mm) hole will be large enough for all three to pass through. 4″ x 2″ (100 x 50mm) - To pass the included water supply line toward the water supply 11/4″ (32mm) diameter - To pass the dishwasher drain hose toward the drain connection Check clearance between dishwasher door and wall Figure 2 Countertop Before sliding the dishwasher into the cabinet, remove the hose clip at the back of the dishwasher as shown in Figure 4. The hose clip may be used later to hold the drain hose as shown in Figure 9. Figure 4 WARNING Avoid Electrical Shock/Fire Hazard Do not allow the electrical and water supply lines to touch. 6 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38

NOTE: This dishwasher is designed to be enclosed on the
top and both sides by standard residential kitchen cabinetry.
Select a location as close to the sink as possible for easy
access to water supply and drain lines.
For proper dishwasher operation and appearance, ensure
that the enclosure is square and has the dimensions shown
If the dishwasher is to be installed in a corner, make sure that
there is adequate clearance to open the door. See
Figure
2
below.
17
7
/
10
(450mm)
22
3
/
5
(575mm)
32-34
1
/
2
(815-875mm)
max 18”
(458mm)
Enclosure Requirements
After locating the proper place for your new dishwasher,
you will need to create any required openings to allow for
passage of the water, drain and electrical line. In order to
avoid interference with the dishwasher when sliding it into the
cabinet, place your openings within the dimensions shown
in
Figure 3
below
.
Required Openings:
4
3
/
4
″ x 2
3
/
8
″ (120 x 60mm)
-
To pass the included electrical
supply junction box through to adjacent cabinet.
Note: If the incoming electric supply, water supply and drain
connections are all in the same cabinet, the one 4
3
/
4
″ x 2
3
/
8
(120 x 60mm) hole will be large enough for all three to pass
through.
4″ x 2″ (100 x 50mm) - To pass the included water supply
line toward the water supply
1
1
/
4
″ (32mm) diameter - To pass the dishwasher drain hose
toward the drain connection
WARNING
Avoid Scalding or Electrical Shock Hazard!
Make sure the water supply and electrical supply
are shut off before installation or service.
Avoid Electrical Shock/Fire Hazard
Do not allow the electrical and water supply lines
to touch.
WARNING
Before sliding the dishwasher into the cabinet, remove the
hose clip at the back of the dishwasher as shown in
Figure
4
. The hose clip may be used later to hold the drain hose as
shown in
Figure 9
.
6
Figure 1
Figure 2
Figure 3
Figure 4
NOTE: If your dishwasher opening width measures
>18 in
(458 mm)
use the
TOP OR SIDE MOUNT
mounting methods.
If your dishwasher opening width measures
17
7
/
10
- 18 in
(
450 - 458 mm)
use the
ALTERNATE SIDE MOUNT
mount-
ing method.
Check clearance
between
dishwasher door
and wall
Countertop
4
1
/
2
"
(114mm)
2
1
/
2
"
(64mm)