Bosch SPX5ES55UC Installation Instructions - Page 9

Drain Connections

Get Bosch SPX5ES55UC PDF manuals and user guides View all Bosch SPX5ES55UC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

max 43" (1100mm) min 20″ (508mm) max 43″ (1100mm) min 20″ (508mm) max 43″ (1100mm) Figure 8 F IMPORTANT NOTES: · If local ordinance require an air gap, install it according to the manufacturer's instructions. · If the dishwasher drain hose is to be connected to a disposer dishwasher drain connection, remove the plug from the disposer's dishwasher drain connection. · The dishwasher drain hose must have one place along its length that is securely attached 20″ (508mm) above the cabinet floor. · The drain hose length can be extended if necessary. The maximum length of the drain hose, including the hose leading to the air gap, is 150″ (3800mm). To connect the hot water supply: 1. Assemble the water supply adaptor fitting (Part F) from the parts bag onto the dishwasher water supply hose. This connection does not require Teflon brand tape. 2. Pass the dishwasher water supply line with attached adaptor through the opening toward the water shut off valve. Take care not to allow the hose to kink or twist behind the dishwasher. 3. Connect the dishwasher water supply line with adaptor to the water shut off valve. You will need to use an approved dishwasher water supply line with the correct fittings for this connection. Always use the appropriate seal when making plumbing connections. NOTE: The end of the dishwasher water inlet hose is heavy and will need to be supported. It is best to lay the end on the cabinet floor as shown in Figure 8. 4. After all connections are made, turn on the hot water and check for leaks. Drain Connections The dishwasher drain hose may be connected to the household or field drain plumbing in one of four ways. You will need a 11/4" diameter hole in order to pass the drain hose through the cabinet. You may use the previously removed drain hose clip to hold the drain hose as shown in Figure 9 if needed. Figure 9 Figure 10 Non-Metallic Tie Figure 11 Non-Metallic Tie MIN. MIN. 20" 20" E E Figure 12 Figure 13 Remove plug E E 1 Directly under the sink dishwasher drain connection, as shown in Figure 10. 2 Directly to a disposer dishwasher drain connection, as shown in Figure 11. 3 To the under sink dishwasher drain connection through an air gap, as shown in Figure 12. 4 To a disposer dishwasher drain connection through an air gap, as shown on Figure 13. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
9
To connect the hot water supply:
1. Assemble the water supply adaptor fitting (Part F) from
the parts bag onto the dishwasher water supply hose.
This connection does not require Teflon brand tape.
2. Pass the dishwasher water supply line with attached
adaptor through the opening toward the water shut off
valve. Take care not to allow the hose to kink or twist
behind the dishwasher.
3. Connect the dishwasher water supply line with adaptor to
the water shut off valve. You will need to use an approved
dishwasher water supply line with the correct fittings for
this connection. Always use the appropriate seal when
making plumbing connections.
NOTE: The end of the dishwasher water inlet hose is
heavy and will need to be supported. It is best to lay the
end on the cabinet floor as shown in
Figure 8
.
4. After all connections are made, turn on the hot water and
check for leaks.
The dishwasher drain hose may be connected to the house-
hold or field drain plumbing in one of four ways. You will need
a 1
1
/
4
” diameter hole in order to pass the drain hose through
the cabinet. You may use the previously removed drain hose
clip to hold the drain hose as shown in
Figure 9
if needed.
1
Directly under the sink dishwasher drain connection, as
shown in
Figure 10
.
2 Directly to a disposer dishwasher drain connection, as
shown in
Figure 11
.
3 To the under sink dishwasher drain connection through
an air gap, as shown in
Figure 12
.
4
To a disposer dishwasher drain connection through an air
gap, as shown on
Figure 13
.
IMPORTANT NOTES:
·
If local ordinance require an air gap, install it according
to the manufacturer’s instructions.
·
If the dishwasher drain hose is to be connected to a
disposer dishwasher drain connection, remove the plug
from the disposer’s dishwasher drain connection.
·
The dishwasher drain hose must have one place along
its length that is securely attached 20″ (508mm) above
the cabinet floor.
·
The drain hose length can be extended if necessary. The
maximum length of the drain hose, including the hose
leading to the air gap, is 150″ (3800mm).
Figure 8
Figure 12
Figure 13
Figure 10
Figure 9
Non-Metallic Tie
Non-Metallic Tie
Figure 11
Remove
plug
Drain Connections
max 43” (1100mm)
E
E
E
E
min 20″ (508mm)
max 43″ (1100mm)
min 20″ (508mm)
max 43″ (1100mm)
F