Home » Bosch Manuals » Laundry Washers » Bosch WAP24202UC » Manual Viewer

Bosch WAP24202UC Instructions for Use - Page 8

Dimensions and clearances required - washing machine

Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Environmentally friendly use of your washer Your new Bosch washing machine is designed to use water, energy and detergent in a highly efficient way to help reduce operating costs, conserve resources and protect the environment. ▯ Utilize the maximum amount of laundry for the appropriate cycle. ▯ Avoid using too much detergent. ▯ Wash normally soiled laundry without a prewash. ▯ Save energy and detergent when washing lightly and normally soiled laundry. ▯ Energy-saving mode: The display panel lighting goes out after a few minutes and Start/Pause flashes. To activate the display, press any button. Energy-saving mode is not activated if a program is running. ▯ If the laundry will be dried in a dryer afterwards, select spin speed according to the dryer manufacturer's instruction. Dimensions and clearances required Appliance dimensions E G ƒ ƒ D F H Length of power cord and water supply hoses To left of washer* To right of washer* U.S. Metric U.S. Metric Electric power 51 in. cord 130 cm 47 in. 119 cm Water supply 53 in. hoses 135 cm 33 in. 84 cm Drain Hose 37 in. 94 cm 55 in. 140 cm * Facing the front of the washer Installation types Stacked washer and dryer A Bosch dryer of the same dimensions can be placed on top of the washer to save space. Use the special washer-dryer sets which can be obtained from customer service or your local dealer (see the dryer user manual). % Label Dimension U.S. Metric a width 23.6 in. 60 cm b depth 25 in. 64 cm (to front of door) c height (minimum*) 33.2 in. 85 cm height (maximum*) 33.8 in. 86 cm d side clearance 15.8 in. 40 cm (door open 180°) e depth 42.5 in. 108 cm (door open 90°) Weight approximate 169.8 lbs. 77.2 kg * height of appliance depends on the extension of the height adjustable appliance feet. ( + ) * & $ ' 8

Section	Page
en-us Use and care manual	1
Washer	1
Table of contentsen-us Use and care manual	3
Important information	4
Purchase information	4
Customer service	4
1. Contact your installer or the Authorized Service Contractor in your area and explain to them why you are not satisfied. This will usually correct the problem.	4
2. If after working with your installer or service technician the problem still has not been resolved to your satisfaction, please let us know either by writing to us at: BSH Home Appliances 1901 Mainstreet, Suite 600 Irvine, CA 92614 or calling us at:	4
Your washing machine is intended for	5
NOTICE:	5
Importance and meaning of symbols	5
9 WARNING	5
warning	5
9 CAUTION	5
caution	5
NOTICE:	5
Tip:	5
IMPORTANT SAFETY INSTRUCTIONS	6
READ AND SAVE THESE INSTRUCTIONS	6
WARNING	6
WARNING	6
IMPORTANT SAFETY INSTRUCTIONS	7
READ AND SAVE THESE INSTRUCTIONS	7
WARNING	7
WARNING	7
Introduction to your new washer	7
9 WARNING	7
risk of fire, electric shock or injury	7
Standard features and helpful information	7
Special features	7
Environmentally friendly use of your washer	8
Dimensions and clearances required	8
Appliance dimensions	8
Length of power cord and water supply hoses	8
Installation types	8
Installation instructions	10
9 WARNING	10
Risk of fire, electirical shock or injury to persons	10
9 CAUTION	10
Washing machine is heavy	10
Introduction	10
NOTICES	10
Tools needed	10
Waste disposal	10
9 WARNING	10
Warnings for children	10
9 WARNING	10
To avoid risk of injury or death, do the following	10
Parts provided with your washer	11
NOTICE:	11
Set up on a pedestal with drawer	11
Installation checklist	11
Importance of installing on a solid, level floor	11
Remove the transport bolts	12
9 CAUTION	12
Damage to the appliance	12
1. Remove hoses from the brackets.	12
2. Loosen and remove all 4 transport bolts. Remove the sleeves. Take the power cable out of the brackets.	12
3. Place covers over the transport bolt holes Four plastic covers are provided in the small parts bag included with your washer. Separate these covers and install one in each hole where the transport bolts were removed. Lock covers firmly by pressing...	12
NOTICE:	12
Water connections	12
NOTICES	12
NOTICES	13
9 WARNING	14
Scalding	14
9 CAUTION	14
Appliance damage/damage to textiles	14
NOTICE:	14
Leveling the washer	14
1. Install the washer on a level and solid surface, preferably in a corner of a room.	14
2. If the floor is uneven (or unlevel) adjust the washer feet as required to level the washer. Do not place anything under the washer feet to help level the washer.	14
3. Extend the washer feet no more than is necessary. The more the feet are extended, the more vibration the washer will experience. Start with the washer feet turned all the way in and adjust each foot as necessary.	14
4. Use a bubble level to check the top of the washer to make sure it is level side to side and front to rear.	14
5. Press down on each corner of the washer top to make sure the washer doesn’t “wobble“. There should be no \	14
6. When the washer is level and does not wobble, lock the washer feet in place by tightening the locknuts against the washer bottom. Be sure to do this without changing the height of the foot (hold the foot while tightening the locknut).	14
1. After determining which washer feet need to be extended, have someone lift up on the washer slightly to take pressure off the foot to be adjusted.	14
2. Turn the grey plastic foot to extend it downward as far as necessary to raise the corner of the washer the correct amount to level the washer.	14
3. When the height of the foot is correct, use a 17 mm open end wrench to tighten the locknut against the washer bottom. The locknut should be tight against the bottom of the washer to lock the foot in place.	14
Electrical connection	14
9 WARNING	14
Electrical shock	14
9 WARNING	14
Electrical Shock	14
9 WARNING	14
Electrical Shock	14
To reduce the risk of electrical shock:	14
Transporting the washer	15
1. Disconnect the washer power cord from the wall outlet.	15
2. Turn off the water supply to the washer.	15
3. Disconnect water supply lines from the tap.	15
4. Disconnect the drain hose from the drain location.	15
5. Install the transport bolt assemblies as shown below.	15
1. Remove all four transport bolt hole covers.	15
2. Pull the tip of the arrow on the cover out slightly to disengage the locking tab.	15
3. Rotate the cover counterclockwise to remove. Repeat for all 4 transport bolt hole covers.	15
1. Each assembly consists of a plastic bushing and a bolt that extends through the bushings. Unscrew the bolt until the threaded end is flush with the end of the plastic bushing.	15
2. Insert the transportation bolt and bushing assembly as shown. The metal housing slides around the bolt through the slot in the plastic bushing as the bushing is slid into place. The open part of the bushing slot should be facing the direction show...	15
3. When the bolt is in place screw it in until the bolt threads engage the drum. Double check and ensure bolts are screwed into threaded holes and not into adjecent cracks or crevices. Repeat the process for all 4 transportation bolt assemblies befor...	15
Getting to know your appliance	16
Control panel	16
Display field	16
Laundry	17
Preparing the laundry	17
NOTICE:	17
Sorting the Laundry	17
Identifying and treating stains	17
Laundry detergents and additives	18
Adding the correct amount of HE detergent	18
9 WARNING	18
warning	18
NOTICE:	18
Cycle selection table	19
Tips	20
Starching	20
NOTICE:	20
Dyeing/bleaching	20
Soaking	20
1. Pour soaking agent/detergent into compartment II in accordance with the manufacturer's instructions.	20
2. Turn the program selector to Cotton Normal Cold program.	20
3. Press Start/Pause.	20
4. After approx. ten minutes, press Start/Pause.	20
5. After the required soaking time, press Start/Pause again to continue or change the program.	20
NOTICES	20
Default cycle settings	21
Changing the temperature range	21
Changing the spin speed range	21
Delay Start	21
NOTICE:	21
1. Press Start/Pause.	21
2. Press the Delay Start button until the desired number of hours is displayed.	21
3. Press the Start/Pause button	21
NOTICE:	21
Additional program settings	21
Extra Rinse	21
Easy Iron	21
Prewash/Pre Treat	21
Operating Instructions	22
9 WARNING	22
warning	22
Before doing any laundry with your washing machine	22
9 WARNING	22
warning	22
Before loading your first load of laundry	22
Using the cycle selector to choose a wash cycle	22
NOTICE:	22
Changing default cycle settings	22
Selecting additional cycle settings	22
Loading the laundry	22
9 WARNING	22
warning	22
Tip:	22
Tips	23
Filling the detergent and additives compartments	23
NOTICE:	23
9 WARNING	23
Irritation of eyes/skin!	23
NOTICE:	23
Tips	23
1. Open the detergent dispenser drawer.	23
2. Add detergent or additive.	23
3. Avoid overfilling the compartment to prevent early dispensing.	23
4. Close the detergent dispenser drawer completely before starting the wash cycle.	23
Tip:	23
1. Pull out the detergent drawer. Press down on the insert and remove the drawer completely.	24
2. Push the liquid detergent dispenser forward.	24
3. Insert the drawer again.	24
NOTICE:	24
Starting the cycle	24
NOTICE:	24
Child lock	24
NOTICE:	24
Selecting a different cycle	24
1. Press Start/Pause.	24
2. Select another cycle.	24
3. Press Start/Pause. The new cycle starts from the beginning.	24
Pausing/Continuing the cycle	24
Cancel cycle	24
1. Press Start/Pause.	24
2. Cool the laundry off: Select Rinse.	24
3. Press Start/Pause.	24
1. Press Start/Pause.	24
2. Select Spin/Drain.	24
3. Press Start/Pause.	24
Cycle end with rinse stop	24
Cycle end	24
NOTICE:	24
Removing laundry/switching the appliance off	24
1. Open the front door of the washer and remove the laundry.	24
2. Turn the cycle selector to the Off position. Appliance is switched off.	24
3. Turn off the water tap.	24
NOTICES	24
Signal	25
Cleaning and maintenance	26
9 WARNING	26
Risk of electric shock!	26
Cleaning the housing and control panel	26
9 WARNING	26
Risk of explosion!	26
Cleaning the drum	26
Descaling the washer	26
NOTICE:	26
Cleaning the detergent dispenser	26
1. Open the dispenser drawer fully. Press down on the drawer catch (1) and pull the drawer (2) from the washer housing.	26
2. Remove the liquid detergent insert (3) by grasping it and pulling it upwards from the detergent dispenser drawer.	26
3. Clean the insert by holding it under warm running water. Lightly wipe away any remaining detergent residue.	26
4. Reinsert the liquid detergent insert and slide the detergent dispenser drawer back into place and close the drawer securely.	26
Tip:	26
Cleaning the water inlet strainers	26
1. Turn off the water tap.	26
2. Turn the cycle selector to any wash cycle (not to Drain or Spin).	26
3. Press Start/Pause and allow 30 seconds to pass.	26
4. Turn the cycle selector to the Off position.	26
1. Remove the hose from the tap.	27
2. Rinse the strainer under running water. Look at the strainer to see if any visible debris is still present. Rinse again if necessary to remove the debris.	27
3. Reconnect the hose to the tap.	27
1. Remove the hose from the inlet on the back of the washer.	27
2. Using narrow pliers, grasp and pull the strainer from the inlet port.	27
3. Rinse the strainer under running water.	27
4. Reconnect the hose to the back of the washer and turn on the water tap. Check to see if water flows by starting a warm water wash cycle.	27
NOTICE:	27
Cleaning the drain pump	27
9 WARNING	27
risk of scalding	27
1. If the washer has not been drained, try to drain it now. Turn the cycle selector to the Spin/Drain cycle, select No spin and press the Start/Pause button. Wait a few moments to let the cycle drain the water from the drum. If the pump is totally bl...	27
2. Shut off the tap so that no more water flows in and has to be drained.	27
3. Open and remove the service cover.	27
4. Loosen the screws and remove the protective film.	27
5. Use the pull-out drain hose located in the pump access opening to drain the remaining water into a suitable container (up to 5.3 U.S. gallons/20 liters of water may be drained). Pull the sealing cap from the hose and lay the hose over the side of ...	28
6. Turn the pump cover counterclockwise to remove it. A small amount of residual water may flow out when the cover is removed. Clean the interior of the pump housing, removing any debris or foreign objects. Check to be sure the impeller wheel at the ...	28
7. Screw the protective film on the pump on again.	28
8. Insert the service cover snap it in, and close it.	28
NOTICE:	28
Troubleshooting	29
Emergency door lock release	29
9 WARNING	29
Risk of scalding	29
9 WARNING	29
Risk of injury	29
9 CAUTION	29
Water damage	29
1. Turn the washer off by rotating the cycle selector to the Off position. Any running program will then be cancelled. Disconnect the mains plug.	29
2. Allow the water in the drum to cool off.	29
3. Allow the washer drum to come to a stand still (no longer spinning).	29
4. Before opening the washer door, perform the drain procedure included in the pump maintenance section following.	29
5. Loosen screws and remove the protective foil.	29
6. The washing machine door can then be opened.	29
7. The door can then be opened.	29
Troubleshooting	29
9 WARNING	29
electric shock	29
1. Turn the cycle selector to Off.	29
2. Disconnect the washer from the power outlet.	29
3. Turn off the water faucet.	29
4. Call Customer Service.	29
NOTICE:	29
Error messages	32
NOTICE:	32
Customer service	32
STATEMENT OF LIMITED PRODUCT WARRANTY	33

Match case Limit results 1 per page

Environmentally friendly use of your

washer

Your new Bosch washing machine is designed to use

water, energy and detergent in a highly efficient way to

help reduce operating costs, conserve resources and

protect the environment.

▯

Utilize the maximum amount of laundry for the

appropriate cycle.

▯

Avoid using too much detergent.

▯

Wash normally soiled laundry without a prewash.

▯

Save energy and detergent when washing lightly and

normally soiled laundry.

▯

Energy-saving mode

: The display panel lighting goes

out after a few minutes and

Start/

Pause flashes. To

activate the display, press any button.

Energy-saving mode is not activated if a program is

running.

▯

If the laundry will be dried in a dryer afterwards, select

spin speed according to the dryer manufacturer’s

instruction.

Dimensions and clearances required

Appliance dimensions

Length of power cord and water supply

hoses

Installation types

Stacked washer and dryer

A Bosch dryer of the same dimensions can be placed on

top of the washer to save space.

Use the special washer-dryer sets which can be obtained

from customer service or your local dealer (see the dryer

user manual).

Label

Dimension

U.S.

Metric

width

23.6 in.

60 cm

depth

(to front of door)

25 in.

64 cm

height (minimum*)

height (maximum*)

33.2 in.

33.8 in.

85 cm

86 cm

side clearance

(door open 180°)

15.8 in.

40 cm

depth

(door open 90°)

42.5 in.

108 cm

Weight

approximate

169.8 lbs.

77.2 kg

* height of appliance depends on the extension of the

height adjustable appliance feet.

To left of washer*

To right of

washer*

U.S.

Metric

U.S.

Metric

Electric power

cord

51 in.

130 cm

47 in.

119 cm

Water supply

hoses

53 in.

135 cm

33 in.

84 cm

Drain Hose

37 in.

94 cm

55 in.

140 cm

* Facing the front of the washer