Bosch WFMC5301UC Pedestal Installation Instructions - Page 7

drawer, step. - not spinning

Page 7 highlights

Figure 17 q Turning the foot out (clockwise) will raise the corner of the appliance, turning the foot in (counter-clockwise) will lower the corner of the appliance. When the corner of the appliance is satisfactorily raised or lowered, lock the height-adjustable feet in place by turning the lock nut counter-clockwise until it locks tightly against the pedestal housing. i It may be necessary to hold the appliance foot with a pair of pliers to keep it from turning while tightening the lock nut. It the foot does turn, it will change the height of the corner. q After making preliminary adjustments, press down on each corner of the appliance to make sure the unit does not wobble. If it does wobble, lower the foot on that corner until the foot touches the floor firmly. 3. For Washers: Fine tune the leveling by placing a small load of laundry in the machine, starting it in spin cycle and then leveling the appliance again. i If the test spin cycle is manually stopped before its completion, then the door may remain locked for 10 seconds. Note: Correct adjustment of feet (equal weight distribution to all feet) is required to minimize vibration and movement of the appliance during operation. 4. Use the supplied 17mm openĆend wrench to securely tighten both locknuts for the front feet against the pedestal. All locknuts must be tightened firmly to prevent the height adjustable feet from moving during appliance use. 5. Slide the ball bearing rails on the pedestal side to the front (see Figure 18). Figure 18 6. Replace the drawer by aligning it to the drawer slides. Ensure slides of pedestal and drawer are aligned correctly (see Figure 19). Correct Incorrect Figure 19 7. Close the drawer. Ensure drawer slides are correctly engaged by freely opening and closing the drawer. d CAUTION Do not use the drawer as a step. For problems with or service on your pedestal contact BSH Home Appliances. Contact information is available in the Customer Service" section of the appliance manual. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24

7
Figure
17
q
Turning
the
foot
out
(clockwise)
will
raise
the
corner
of
the
appliance,
turning
the
foot
in
(counter-clockwise)
will
lower
the
corner
of
the
appliance.
When
the
corner
of
the
appliance
is
satisfactorily
raised
or
lowered,
lock
the
height-adjustable
feet
in
place
by
turning
the
lock
nut
counter-clockwise
until
it
locks
tightly
against
the
pedestal
housing.
i
It
may
be
necessary
to
hold
the
appliance
foot
with
a
pair
of
pliers
to
keep
it
from
turning
while
tightening
the
lock
nut.
It
the
foot
does
turn,
it
will
change
the
height
of
the
corner.
q
After
making
preliminary
adjustments,
press
down
on
each
corner
of
the
appliance
to
make
sure
the
unit
does
not
wobble.
If
it
does
wobble,
lower
the
foot
on
that
corner
until
the
foot
touches
the
floor
firmly.
3.
For
Washers:
Fine
tune
the
leveling
by
placing
a
small
load
of
laundry
in
the
machine,
starting
it
in
spin
cycle
and
then
leveling
the
appliance
again.
i
If
the
test
spin
cycle
is
manually
stopped
before
its
completion,
then
the
door
may
remain
locked
for
10
seconds.
Note:
Correct
adjustment
of
feet
(equal
weight
distribution
to
all
feet)
is
required
to
minimize
vibration
and
movement
of
the
appliance
during
operation.
4.
Use
the
supplied
17mm
openĆend
wrench
to
securely
tighten
both
locknuts
for
the
front
feet
against
the
pedestal.
All
locknuts
must
be
tightened
firmly
to
prevent
the
height
adjustable
feet
from
moving
during
appliance
use.
5.
Slide
the
ball
bearing
rails
on
the
pedestal
side
to
the
front
(see
Figure
18).
Figure
18
6.
Replace
the
drawer
by
aligning
it
to
the
drawer
slides.
Ensure
slides
of
pedestal
and
drawer
are
aligned
correctly
(see
²Figure
19
).
Correct
Incorrect
Figure
19
7.
Close
the
drawer.
Ensure
drawer
slides
are
correctly
engaged
by
freely
opening
and
closing
the
drawer.
d
CAUTION
Do
not
use
the
drawer
as
a
step.
For
problems
with
or
service
on
your
pedestal
contact
BSH
Home
Appliances
.
Contact
information
is
available
in
the
²
Customer
Service
"
section
of
the
appliance
manual.