Bose LS38BK Installation Guide - Page 22

Your system is now ready for power - outlet stores

Page 22 highlights

BASIC SYSTEM CONNECTIONS Français Español English BASIC SYSTEM CONNECTIONS If your TV does not have a menu setting, follow the instruction (below) to use the on/off switch. If your TV has neither a switch nor a menu option for turning off the internal speakers, reduce the TV volume to its lowest setting. Using your TV speaker on/off switch: If the rear panel of your TV has a SPEAKER ON/OFF switch, set it to the OFF position and adjust the TV volume to about 80% of the maximum. Selecting the FIXED audio output option on your TV If you connected the media center to audio output jacks labeled FIX/VAR (or with no  indication if they are fixed or variable) follow these instructions. 1. Using your TV remote, display the audio menu on your TV screen.  In most cases this can be done by pressing the Menu button and selecting Audio. 2. Turn off the TV speakers (if you have not already done so) as described above. 3. Locate the Audio Output item and select Fixed. 4. Exit the audio menu on your TV screen. If your TV does not provide Fixed audio as an option, but you were able to turn off the internal speakers, set your TV volume to about 80% of the maximum. Your system is now ready for power Note: Bose recommends using a high-quality surge suppressor on all electronics equipment. Voltage variations and spikes can damage electronic components in any system. A quality suppressor can eliminate the vast majority of failures attributed to surges and may be purchased at electronics stores. Connect the two AC power (mains) cords in the following order: 1. On the connector panel of the Acoustimass® module, plug the appropriate end of the  Acoustimass module power cord into the AC power jack (Figure 17). 2. Insert the other end of the power cord into the AC (mains) outlet. 3. Turn the Acoustimass module POWER switch to on. Figure 17 Power connection for the Acoustimass module Acoustimass module connector panel AUDIO INPUT OUTPUTSTO CUBE SPEAKERS FRONT SURROUND L C L R R POWER 100-120/200-240VAC 50/60 Hz 350W MAX. I=on 0=off POWER switch AC power jack AC (mains) outlet 4. If you have not yet plugged the small round connector of the media center power supply cord into the DC POWER jack on the media center connection panel, do so now  (Figure 18). 22 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42

22
B
ASIC
S
YSTEM
C
ONNECTIONS
B
ASIC
S
YSTEM
C
ONNECTIONS
English
Français
Español
If your TV does not have a menu setting, follow the instruction (below) to use the on/off
switch.
If your TV has neither a switch nor a menu option for turning off the internal speakers, reduce
the TV volume to its lowest setting.
Using your TV speaker on/off switch:
If the rear panel of your TV has a SPEAKER ON/OFF switch, set it to the OFF position and
adjust the TV volume to about 80% of the maximum.
Selecting the FIXED audio output option on your TV
If you connected the media center to audio output jacks labeled FIX/VAR (or with no
indication if they are fixed or variable) follow these instructions.
1.
Using your TV remote, display the audio menu on your TV screen.
In most cases this can be done by pressing the Menu button and selecting Audio.
2.
Turn off the TV speakers (if you have not already done so) as described above.
3.
Locate the Audio Output item and select Fixed.
4.
Exit the audio menu on your TV screen.
If your TV does not provide Fixed audio as an option, but you were able to turn off the internal
speakers, set your TV volume to about 80% of the maximum.
Your system is now ready for power
Note:
Bose recommends using a high-quality surge suppressor on all electronics equipment.
Voltage variations and spikes can damage electronic components in any system. A quality
suppressor can eliminate the vast majority of failures attributed to surges and may be purchased
at electronics stores.
Connect the two AC power (mains) cords in the following order:
1.
On the connector panel of the Acoustimass
®
module, plug the appropriate end of the
Acoustimass module power cord into the AC power jack (Figure 17).
2.
Insert the other end of the power cord into the AC (mains) outlet.
3.
Turn the Acoustimass module POWER switch to on.
Figure 17
Power connection for
the Acoustimass module
±²³´²³µ³±
¶²·¸¹µ´¸º»¸¼µ
º²½¾±
¾¿´²³
´±À¸¼
Á¼±¿³
µ²¼¼±²¿½
ÂÃÃÄÂÅÃÆÅÃÃÄÅÇÃȺ¶
ÉÃÆÊùËÌ
ÍÉÃÀ¹ÎºÏÐ
Ñ
¼
Ñ
¼
Acoustimass module
connector panel
POWER switch
AC (mains)
outlet
AC power jack
I=on
0=off
4.
If you have not yet plugged the small round connector of the media center power supply
cord into the DC POWER jack on the media center connection panel, do so now
(Figure 18).