Brother International ADS-1000W Network Users Guide - Page 24

Windows Vista, Windows, Start, Network, Add a wireless device, Devices and Printers, Add a device - manual

Get Brother International ADS-1000W PDF manuals and user guides View all Brother International ADS-1000W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Configuring Your Machine for a Wireless Network (ADS-1000W/ADS-1100W) a Using a small, pointed object, press the AOSS/WPS Button on the back of the machine for about 15 seconds. 3 NOTE The machine will beep after the button is pressed for two seconds. Continue to press the button. b Using a computer connected to the network, type "http://access point's IP address/" into your browser (where "access point's IP address" is the IP address of the device that is used as the Registrar 1). 1 The Registrar is normally the WLAN access point/router. c Go to the WPS setting page, type the PIN indicated on the label at the bottom of the machine into the Registrar, and follow the on-screen instructions. NOTE The setting page is different, depending on the brand of access point/router you are using. See the instruction manual supplied with your access point/router. Windows Vista®/Windows® 7/Windows® 8 3 If you are using your computer as a Registrar, follow these steps: NOTE • To use a Windows Vista®, Windows® 7, or Windows® 8 computer as a Registrar, you need to register it to your network in advance. See the instruction manual that came with your WLAN access point/router. • If you use Windows® 7 or Windows® 8 as a Registrar, you can install the scanner driver after the wireless configuration by following the on-screen instructions. If you want to install the full driver and software package, follow the steps in the Quick Setup Guide for installation. 1 (Windows Vista®) Click (Start) > Network > Add a wireless device. (Windows® 7) Click (Start) > Devices and Printers > Add a device. 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
Configuring Your Machine for a Wireless Network
21
3
(ADS-1000W/ADS-1100W)
a
Using a small, pointed object, press the AOSS/WPS Button on the back of the machine for about 15
seconds.
NOTE
The machine will beep after the button is pressed for two seconds. Continue to press the button.
b
Using a computer connected to the network, type "http://access point's IP address/" into your browser
(where "access point's IP address" is the IP address of the device that is used as the Registrar
1
).
1
The Registrar is normally the WLAN access point/router.
c
Go to the WPS setting page, type the PIN indicated on the label at the bottom of the machine into the
Registrar, and follow the on-screen instructions.
NOTE
The setting page is different, depending on the brand of access point/router you are using. See the
instruction manual supplied with your access point/router.
Windows Vista
®
/Windows
®
7/Windows
®
8
3
If you are using your computer as a Registrar, follow these steps:
NOTE
•
To use a Windows Vista
®
, Windows
®
7, or Windows
®
8 computer as a Registrar, you need to register it
to your network in advance. See the instruction manual that came with your WLAN access point/router.
•
If you use Windows
®
7 or Windows
®
8 as a Registrar, you can install the scanner driver after the wireless
configuration by following the on-screen instructions. If you want to install the full driver and software
package, follow the steps in the Quick Setup Guide for installation.
1
(Windows Vista
®
)
Click
(
Start
) >
Network
>
Add a wireless device
.
(Windows
®
7)
Click
(
Start
) >
Devices and Printers
>
Add a device
.