Brother International BAS-311F-0 Instruction Manual - English - Page 69
Changing Special Function And Using The Memory Switches, Memory Switches 30 - 3f
View all Brother International BAS-311F-0 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 69 highlights
11. CHANGING SPECIAL FUNCTION AND USING THE MEMORY SWITCHES Memory switches (30 - 3F) Turn the dial while pressing the STEP BACK switch to change the values. Switch No. memo-30 memo-31 memo-32 memo-33 memo-34 memo-35 memo-36 memo-37 memo-38 memo-39 memo-3A memo-3b Possible setting range 1 - 999 1 - 4 1 - 7 1 - 10 1 - 5 10 - 60 1 - 3 0 - 3 1 - 20 0 - 11 1 - 3 - Units X 10ms X 7.5 stitch ms X 100 ms - - - Initial Value 10 1 3 5 Explanation Time until feed mechanism starts moving after work clamp has lifted. Changes the feed speed. 1 (Fast) 4 (Slow) Changes the possible sewing speed for a given stitch length. 1 (Fast) 7 (Slow) 1 (2,700/3 mm), 2 (2,600/3 mm), 3 (2,500/3 mm), 4 (2,300/3 mm), 5 (2,000/3 mm), 6 (1,800/3 mm), 7 (1,200/3 mm) Settings 1 and 2 are outside the warranty specification at the time of shipment from the factory.) Changes the feed timing. 1 (Fast) 5 (standard) 10 (Slow) 1 Number of low-speed stitches sewn at 400 rpm at sewing start. Solenoid ON time changes (BAS-311F solenoid specifications 40 only). 10 (Quiet) 60 (High work clamp capacity) 1 The solenoid ON time when the presser foot is raised changes. (Standard) 1 3 (Upper limit) Automatically corrects the gear speed when reading 2DD disks. 0 : No automatic correction 0 1 : Read as BAS-311A data 2 : Read as BAS-326A data 3 : Read as BAS-341A, 342A data ex. Read BAS-326A data by BAS-311F / Set memo-37=2 Changes the length of time from inserting the cassette until 1 automatic starting when the eject device is being used and automatic starting has been set (memo-03 and DIP switch A-7 are also both ON). Changes the reference point for enlargement and reduction using the operation panel. 0 : Sensor home position 1 : Center of work clamp 2 : Upper-left corner of work clamp 3 : Lower-left corner of work clamp 0 4 : Upper-right corner of work clamp 5 : Lower-right corner of work clamp 6 : Sewing start point, 7 : Sewing end point 8 : Upper-left corner of sewing pattern 9 : Lower-left corner of sewing pattern 10 : Upper-right corner of sewing pattern 11 : Lower-right corner of sewing pattern Changes the speed limit for the given sewing pitch when the maximum speed remains constant. 1 : Speed limit is increased for the given sewing pitch and the sewing speed for that pitch is increased. 2 : Standard 2 3 : Speed limit is decreased for the given sewing pitch and the sewing speed for that pitch is decreased. Note If sewing slippage occurs in places where a large sewing pitch is used, reduce the setting to 3. Furthermore, sewing slippage may occur in some cases if setting 1 is used. 0- memo-3c - - 0- memo-3d - - 0- memo-3E - - 0- memo-3F - - 0 BAS-311F-0, 311F-L, 326F-0 62